基于AFM的微结构加工实验研究

本文建立了微动工作台和原子力显微镜相结合的微加工系统，在该系统上采用金刚石针尖进行微加工实验，与SPI系统本身的刻划软件刻划出的图形进行了比较分析，得出这个系统适合微结构的加工；并给出了采用该方法加工的1111面及多边形面微结构；还分析了金刚石针尖几何角度及SPM和工作台的相关参数对加工的影响。     

COMPRESSION FATIGUE CRACK GROWTH BEHAVIOUR OF AN ALUMINIUM ALLOY: EFFECT OF OVERLOADING

Abstract— The behaviour of fatigue cracks in an Al-alloy under cyclic compression, either with or without overloads, was studied. For constant-amplitude compressive cycling, a non-catastrophic (saturation) character of the fatigue crack behaviour was confirmed, with the final depth of a crack depending on the applied load level. Single (tensile or compressive) intermittent overloads were shown to re-activate a previously arrested crack while reversed (tensile—compressive or compressive—tensile) ones were also shown to maintain continual fatigue crack extension under otherwise fully compressive cycling.     

轴向磁场无铁心无刷永磁盘式电机的设计

介绍了轮用轴向磁场无铁心无刷永磁盘式电机的结构形式，探讨了这种新电机的设计特点，重点解决了电机主要尺寸确定和磁路分析计算问题，最后给出了一种磁极形状和线圈形状的优选方案。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

圆盘锯机性能提升途径

圆盘锯机在线材厂投入使用时不能满足生产的需要：锯切周期太长，锯片使用性能差，经过对设备进行技术改造和对设备操作规程进行优化，以及在操作上加强管理，使之关键指标大幅度提升，为圆盘锯机的使用改善提供了新的思路。     

潜油电机碟形弹簧的动力学分析

为了降低潜油电泵机组的振动对止推轴承性能的影响,在潜油电机中节和下节的止推轴承静块底部安装了蝶形弹簧。用有限元方法进行模态分析,确定了蝶形弹簧的主振型和固有频率,然后进行瞬态动力学分析,求解蝶形弹簧在一定载荷下的应力和位移。依此设计的蝶形弹簧将进一步延长止推轴承的使用寿命。     

泥沙起动条件及机理的非线性研究

 分析了单颗粒、均匀沙及非均匀沙的起动现象及其机理，认为泥沙的起动属于突变论研究的范畴。从泥沙起动所遵循起动条件的力学规律出发，导出泥沙起动条件方程。在此基础上，利用尖点突变性质对各种泥沙起动现象及机理进行了描述和说明。     

Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.