NADRA 3D information technology for analysis of processes in multicomponent soil media

This paper considers the principles of algorithmic and software implementation of the software system NADRA 3D designed to analyze processes in three-dimensional multicomponent soil media. The principles of operation of NADRA 3D are described. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 6, pp. 157–174, November–December 2006.     

Failure analysis of a wire rope

Wire ropes, pulleys, counterweights, and connecting systems are used for auto tensioning of contact wires of electric railways. A wire rope in one such auto tensioning system suffered premature failure. Failure investigation revealed fatigue cracks initiating at nonmetallic inclusions near the surface of individual wire strands in the rope. The inclusions were identified as Al-Ca-Ti silicates in a large number of stringers, and some oxide and nitride inclusions were also found. The wire used in the rope did not conform to the composition specified for AISI 316 grade steel, nor did it satisfy the minimum tensile strength requirements. Failure of the wire rope was found to be due to fatigue; however, the ultimate fracture of the rope was the result of overload that occurred after fatigue failure had reduced the number of wire strands supporting the load.     

铝液夹杂物检测DMIRT－Ⅲ法的试验研究

提出了一种新的铝液夹杂物快速检测方法。导出了该法的检测原理方程。分析并试验研究了影响检测重复性和分辨率的因素。试验选择了较好的检测参数，并获得了较好的检测结果。     

非金属夹杂物对硬线盘条拉拔性能的影响及其工艺控制

分析了非金属夹杂物对硬线盘条拉拔性能的影响及其来源 ,通过考察分析冶炼、浇注生产工艺针对非金属夹杂物含量的影响 ,提出了避免或减少非金属夹杂物含量的工艺控制方法。     

中间包CaO质陶瓷过滤器滤除夹杂效果的研究

对鞍钢三炼钢厂中间包应用的CaO质陶瓷过滤器进行了实验研究，从装有陶瓷过滤器和未装陶瓷过滤器的挡墙侧水口上方及各自的连铸坯中取样，并用电解法和吸收光度法测定了夹杂物的总含量及分量。实验结果表明，陶瓷过滤器对于滤除钢液中的Al2O3、SiO2夹杂作用显著。     

含Zr低合金高强度钢中夹杂物的特性

用电子探针研究了含Zr低合金高强度钢中夹杂物的形貌、大小及分布等特性。结果表明 ,钢样中的夹杂物为圆形 ,呈分散分布 ,其组成系含ZrO2 的复合夹杂物 ,而且MnS依附此复合夹杂物成核和长大。钢中添加少量Zr可明显改善夹杂物形态和分布 ,从而改善钢的强度和韧性     

On formalism and stability of switched systems

In this paper,we formulate a uniform mathematical framework for studying switched systems with piecewise linear partitioned state space and state dependent switching.Based on known results from the the...     

LF软吹时间对硅脱氧弹簧钢氧化物夹杂控制影响

 对于一些采用硅锰脱氧冶炼工艺的特殊钢,为保证钢水洁净度,常会选择较长时间的LF软吹处理,导致过程能耗增加。通过工业试验,借助FEI Explorer 4自动扫描电镜检测,研究不同LF精炼软吹时间对硅脱氧弹簧钢55SiCr铸坯氧化物夹杂成分、数量的影响;并采用夹杂物极值统计法,对比评价不同LF精炼软吹时间对应成品盘条横截面最大夹杂物尺寸控制情况。结果表明,在LF软吹10 min与软吹40 min 两种工艺条件下,铸坯中尺寸大于5 μm的氧化物夹杂成分接近,均在CaO-SiO₂-Al₂O₃相图中假硅灰石、钙长石和钙铝黄长石共晶低熔点区,其中软吹10 min工艺铸坯氧化物夹杂组成落入低熔点区的数量所占比例更大。LF软吹10 min与软吹40 min铸坯中尺寸大于5 μm的氧化物夹杂数量密度分别为11.70个/100 mm2和14.59个/100 mm2,尺寸大于15 μm 的氧化物夹杂数量密度分别为0.53个/100 mm2和1.65个/100 mm2,LF软吹10 min工艺铸坯大尺寸氧化物夹杂数量密度略低于LF软吹40 min工艺。当预测面积为30 000 mm2时,两种LF软吹时间对应成品盘条横截面最大夹杂物尺寸分别为27.1 μm和28.1 μm,盘条最大夹杂物尺寸控制无显著差别。结合硅锰脱氧钢中大尺寸低熔点CaO-SiO₂-Al₂O₃系夹杂物主要源自钢包渣乳化卷入,具有与钢水和氩气泡界面接触角很小、难以通过吹氩上浮去除的特点,建议硅锰脱氧钢LF软吹过程按短时间快节奏进行控制。     

硫化物改质对20MnCr5齿轮钢夹杂物和切削性能的影响

 齿轮钢广泛应用于汽车、机械等传动系统,易切削化是提高齿轮加工效率、降低制造成本的主要途径之一。提高钢中硫元素含量是改善齿轮钢切削性能的有效方式,然而过多的硫元素在轧制时会形成条带状MnS,增大钢的各向异性,因此需要对硫化物进行改制处理。分别采用Ca处理和Mg处理两种方式对20MnCr5齿轮钢进行硫化物改质,通过对力学性能、组织形态、夹杂物分布以及切削性能等表征,对比分析不同改制方式对材料的影响。结果表明,Ca处理和Mg处理后试验钢的强度和塑性保持一致,而Mg处理试样的晶粒尺寸较小,因而韧性较高。Ca处理试验钢中MnS夹杂物数量较多,长条状夹杂物比例相对较高;而采用Mg处理可以有效降低钢中夹杂物的数量,夹杂物平均尺寸有所增大,同时小长径比夹杂物数量增多,但是复合氧化物型夹杂物的数量也有所增加。在240~280 m/min条件下进行了干切削试验,结果表明两种试验钢均出现前刀面磨损、后刀面磨损和边界磨损,其中Ca处理试样的刀具磨损较为严重,同时在较高切削速度下出现了积屑瘤和崩角现象,而Mg处理试样则具有更长的刀具使用寿命,对切削速度的敏感性也较低。分析可知,Mg处理后钢中存在较多的大尺寸球状硫化物夹杂物,提高了应力集中效应,更有利于改善切削性能,因而改制效果更好。     

Carbon segregation and inclusions effects on surface fracture morphology of a 12% chromium stainless steel

Martensitic 12% chromium stainless steel is generally used for the manufacture of water vapour turbine blades. This material, under these environmental conditions, develops fatigue corrosion with failure as a result of the segregation of certain constituent elements such as phosphorus (P) and sulphur (S),^[1–3] or the presence of some types of inclusions.^[2–4] To be able to understand and explain these phenomena, in situ characterization of the fractured surfaces were performed for two types of samples: steel 1 as manufactured turbine material whose fracture mode is intergranular and steel 2 issued from last stage turbine blades after 100 000 h service at 40 °C whose fracture mode is transgranular. The techniques used for characterization were scanning electron microscopy (SEM) coupled with the x-ray analysis by energy dispersive spectroscopy (EDS), and auger electron spectroscopy (AES). The Auger results enabled the understanding of the brittle to ductile transition for the material by showing the simultaneous diffusion of carbon from grain boundaries (GB) to grains (G) and chromium from G to GB. Furthermore, the heavy segregation of phosphorus at the GBs could explain the intergranular crack rupture traces observed in steel 2. SEM observations coupled with EDS analysis showed the presence of different types of non-metallic inclusions such as silicon-based complex inclusions and manganese sulfides (MnS). The presence of silicon-based complex inclusions at GB could explain the intergranular fracture mode previously reported. The characterization of the fracture appearance suggests also that MnS inclusions can act as nucleation sites for secondary microcracks at the GB level that were observed after service.