磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

随钻扩眼工具及技术研究

基于随钻扩眼技术优势的分析，研究了机械式、液压式和偏心式随钻扩眼工具执行机构和扩眼总成的机构原理，并介绍了国内所开展的相关研究。文章提出应加强现有工具的适应性和匹配性研究，发掘各类工具的优势。优化执行机构、扩眼总成和水力机构、重视底部钻具组合力学特性的分析是今后发展和完善随钻扩眼工具及技术的几个重要内容。实践表明，随钻扩眼技术在处理井下复杂情况、降低钻井综合成本、提高钻井速度、提高建井质量和安全性等方面具有显著的优势，随钻扩眼工具也正逐渐成为一种重要的石油钻井配套工具。     

铜铅锌银多金属矿湿法分离新工艺

依据不同金属硫化物氧化分解电位的差异 ,针对某含铜、铅、锌、银复杂多金属硫化矿的难选冶特性 ,对浮选获得的混合精矿采取在线控制浸出过程氧化还原电位的方法 ,分步选择性氯化浸出各有价元素 ,并辅之以沉淀、置换、萃取等工艺 ,使有价金属以较高的回收率得到了有效的分离提取 ,在各工序最佳条件下 ,Cu、Pb、Zn、Ag各金属的浸出率均大于 99 0 % ,元素硫的回收率大于 76%     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

难处理金矿石加石灰焙烧焙砂中CaS的消除

介绍了用空气氧化预浸加石灰焙烧焙砂中的CaS，以消除其对金氰化的影响。预浸后金的氰化浸出率可从58％提高到80％以上。     

硫脲法浸金研究

研究了用硫脲法浸取硫化金矿时．矿石预处理、硫脲浓度、硫酸铁浓度、酸度、浸取时间、固液比等实验条件对金浸出率的影响，并对结果进行了讨论．     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

无线随钻测量技术的应用现状与发展趋势

目前,无线随钻测量技术是石油工程技术发展的一个主要方向。详细介绍了无线随钻测量仪器的传输方式、国内外无线随钻测量技术的主要进展和应用现状,指出了国内外无线随钻测量仪器的优缺点和应用范围,分析了无线随钻测量技术的发展趋势,并提出我国应在借鉴国外先进的无线随钻测量技术的基础上,研制具有自主知识产权的无线随钻测量仪器,以加快我国无线随钻测量技术的发展,缩短与国际先进水平的差距。