Performance of BaZrO3/Y2O3 dual-phase refractory applied to TiAl alloy melting

Vacuum induction melting is a potential process for the preparation of TiAl alloys with good homogeneity and low cost. But the crucial problem is a selection of high stability refractory. In this study, a BaZrO₃/Y₂O₃ dual-phase refractory was prepared and its performance for melting TiAl alloys was studied and compared with that of a Y₂O₃ refractory. The results showed the dual-phase refractory consisted of BaZr_1-xY_xO_3-δ and Y₂O₃(ZrO₂), exhibited a thinner interaction layer (30 μm) than the Y₂O₃ refractory (90 μm) after melting the TiAl alloy. Although the TiAl alloys melted in the dual-phase and Y₂O₃ refractory exhibited similar oxygen contamination (<0.1 wt%), the alloy melted in the dual-phase refractory had smaller Y₂O₃ inclusion content and size than that in the Y₂O₃ refractory, indicating that the dual-phase refractory exhibited a better melting performance than the Y₂O₃ refractory. This study provides insights into the process of designing highly stable refractory for melting TiAl alloys.     

SLM printing of cermet powders: Inhomogeneity from atomic scale to microstructure

It is very challenging for 3D printing based on the selective laser melting (SLM) technology to obtain cermet bulk materials with high density and homogeneous microstructures. In this work, the SLM process of the cermet powders was studied by both simulations and experiments using the WC-Co cemented carbides as an example. The results indicated that the evolution of the ceramic and metallic phases in the cermet particle during the heating, melting and solidification processes were all significantly inhomogeneous from atomic scale to mesoscale microstructures. As a consequence, the microstructural defects were caused intrinsically in the printed bulk material. The formation and growth of the bonding necks between the particles were mainly completed at the later stage of laser heating and the early stage of solidification. Both simulations and experiments demonstrated that thin amorphous layers formed at the ceramics/metal interfaces. This work disclosed the mechanisms for the evolution from the atomic scale to microstructure during the SLM printing of cermet powders, and discovered the origin of the defects in the printed cermet bulk materials.     

Study on ice-melting performance of gradient gas diffusion layer in proton exchange membrane fuel cell

In this study, a three-dimensional model was established using the lattice Boltzmann method (LBM) to study the internal ice melting process of the gas diffusion layer (GDL) of the proton exchange membrane fuel cell (PEMFC). The single-point second-order curved boundary condition was adopted. The effects of GDL carbon fiber number, growth slope of the number of carbon fibers and carbon fiber diameter on ice melting were studied. The results were revealed that the temperature in the middle and lower part of the gradient distribution GDL is significantly higher than that of the no-gradient GDL. With the increase of the growth slope of the number of carbon fiber, the temperature and melting rate gradually increase, and the position of the solid-liquid interface gradually decreases. The decrease in the number of carbon fibers has a similar effect as the increase in the growth slope of the number of carbon fibers. In addition, as the diameter of the carbon fiber increases, the position of the solid-liquid interface gradually decreases first and then increases.     

中子平衡节块离散纵标法及CMFD加速技术研究

本文基于横向积分离散纵标方程,解析得到横向积分通量中出射通量与入射通量的关系,并根据类似于扩散方程节块展开法的输运节块中子平衡方程形式,得到了一种高效的节块离散纵标法数值迭代策略。数值结果表明,本文提出的方法可行且数值结果正确。此外,粗网有限差分(CMFD)加速技术在节块离散纵标法中也取得了非常好的应用效果。     

Laser induced fast ignition made realistic by relativistic velocities-dream or reality?

Due to the recent developments in high power lasers it is suggested to accelerate a micro-foil by the laser pressure to relativistic velocities. The time dependent velocity of this micro-foil is calculated analytically for pulsed constant laser intensity. The accelerated foil collides with a target creating a shock wave on impact. The shock wave parameters are calculated within the context of relativistic fluid dynamics.It is suggested to use the energy of the relativistic micro-foil to ignite a pre-compressed target with a density relevant for fusion ignition. The equations are written and solved for the collision between the micro-foil and the very dense target. The criteria for shock wave ignition and heat wave ignition are used to show that one needs significantly less laser energy for heat wave ignition.The present scheme shows that nuclear fast ignition by micro-foil impact could be attained in the near future with lasers that are currently under construction.     

基于振动实测的非均质地层钻头失效分析与对策

四川盆地作为国内页岩气开发的重点区域,通过近几年的不断攻关和实践,机械钻速得到了提高,但由于受地层复杂、可钻性差、非均质性强等地质因素的影响,导致井下钻柱系统不良振动剧烈,容易出现钻头损坏严重、钻速较低等问题,严重影响了钻井时效。为了解决上述难题,以该盆地涪陵工区上二叠统龙潭组—中二叠统茅口组为例,采用井下振动高频测量工具的实测手段,测量了钻头—钻柱系统的动态振动加速度参数,结合地层的岩性和矿物组分分析,研究钻头失效原因与对策,并开展了现场试验。研究结果表明:①在非均质地层中钻进的钻头—钻柱系统产生了大于40 m/s~2的高幅值瞬时冲击振动,高幅值的瞬时冲击是导致钻头先期失效的主要原因;②提出了抑制高幅值的瞬时冲击振动采用"减振+增压"工具组合和避免井下工具共振的钻井参数;③采用钻井新参数的试验井比邻井的高幅值瞬时振动降低了17%,单只钻头进尺增加24%,钻头工作环境得到了较大的改善,钻头使用数量减少。结论认为,该研究成果能够有效地改善钻头—钻柱系统的振动状态,有利于达成延长钻头使用寿命的目标。     

烟机结垢的成因分析及防范措施

通过对烟机垢物的元素和晶体组成进行表征，分析其形成条件，计算验证并探讨垢物的形成过程，并提出应对防范措施。烟机结垢过程为：极少数原料油滴在反应汽化段内未完全汽化，未汽化油黏附在催化剂细粉表面并缩合生焦；部分焦炭颗粒未在再生器内烧尽，进入烟道后继续燃烧达到细粉的熔融温度，转化为液相黏性物质；携带微量高温熔融粉尘的烟气在三级旋风分离器下料口、烟机叶片等部位受高速离心作用，黏附到易结垢部位，形成无定形垢物。可通过提升原料油喷嘴雾化效果，调整合适的剂油比和系统细粉含量来减少烟机结垢。     

橡胶促进剂DM的合成工艺

M氧化生成DM是自由基反应机理，结合微反应器机理，采用分子氧化的反应方式，选用绿色溶剂异丙醇、环境友好型氧化剂H202，一步法制取高品质DM。对反应时间、反应温度、氧化剂用量等因素进行考察，确定最佳工艺条件为：反应时间90min，反应温度55℃，氧化剂不过量，碱过量5％，M—Na溶液M含量30％，加料时N60 min，溶剂用量为M—Na溶液质量的1．5倍，所得产品质量合格，熔点可达180℃。     

邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.