全文获取类型
收费全文 | 33033篇 |
免费 | 5279篇 |
国内免费 | 3118篇 |
专业分类
电工技术 | 1477篇 |
技术理论 | 1篇 |
综合类 | 4591篇 |
化学工业 | 3013篇 |
金属工艺 | 3526篇 |
机械仪表 | 2897篇 |
建筑科学 | 4563篇 |
矿业工程 | 3017篇 |
能源动力 | 3092篇 |
轻工业 | 403篇 |
水利工程 | 3088篇 |
石油天然气 | 2551篇 |
武器工业 | 1335篇 |
无线电 | 1080篇 |
一般工业技术 | 3402篇 |
冶金工业 | 1299篇 |
原子能技术 | 555篇 |
自动化技术 | 1540篇 |
出版年
2024年 | 170篇 |
2023年 | 524篇 |
2022年 | 1176篇 |
2021年 | 1255篇 |
2020年 | 1370篇 |
2019年 | 1061篇 |
2018年 | 1061篇 |
2017年 | 1384篇 |
2016年 | 1633篇 |
2015年 | 1648篇 |
2014年 | 2231篇 |
2013年 | 2181篇 |
2012年 | 3040篇 |
2011年 | 2950篇 |
2010年 | 2173篇 |
2009年 | 2227篇 |
2008年 | 1944篇 |
2007年 | 2513篇 |
2006年 | 2156篇 |
2005年 | 1745篇 |
2004年 | 1396篇 |
2003年 | 1093篇 |
2002年 | 825篇 |
2001年 | 734篇 |
2000年 | 569篇 |
1999年 | 434篇 |
1998年 | 350篇 |
1997年 | 319篇 |
1996年 | 268篇 |
1995年 | 195篇 |
1994年 | 191篇 |
1993年 | 126篇 |
1992年 | 115篇 |
1991年 | 74篇 |
1990年 | 77篇 |
1989年 | 42篇 |
1988年 | 20篇 |
1987年 | 27篇 |
1986年 | 22篇 |
1985年 | 5篇 |
1984年 | 12篇 |
1983年 | 6篇 |
1982年 | 13篇 |
1981年 | 5篇 |
1980年 | 5篇 |
1979年 | 12篇 |
1978年 | 8篇 |
1977年 | 6篇 |
1959年 | 10篇 |
1951年 | 18篇 |
排序方式: 共有10000条查询结果,搜索用时 15 毫秒
1.
以重庆市甄子岩29号危岩体为研究对象,基于现场调查和分析解剖,建立UDEC离散元数值计算模型,对其演化变形过程进行模拟分析。研究表明,在巨大的自重作用下,由于基座岩体岩质软,岩体较破碎,且基座外侧为直立的陡崖,具有完整的临空面,从而使基座岩体易发生压缩流变及剪切流变,进而使危岩体存在滑移垮塌的危险。 相似文献
2.
3.
水平井压裂技术在低渗透及非常规储层中得到了广泛应用,压裂后水平井的产能预测关系到油田开发方案的制定,因此,国内外学者对压后渗流模型的建立和求解方法做出了不懈的努力。本文详细回顾了国内外学者所建压裂水平井产能预测模型及求解方法,指出了不同模型和求解方法的优缺点,并展望了压裂水平井产能模型的发展方向。 相似文献
4.
常规的冲击钻井工具不能满足井眼轨迹控制要求、使用寿命有限、缓解脱压不显著等问题,影响了在定向井钻井中的推广应用。建立248;215.9 mm PDC钻头和岩石的有限元模型,分析钻井参数对破岩效率的影响规律,结果表明:冲击频率为17.5 Hz和35 Hz时,破岩效率最优; 破岩效率随钻压增大而增加,而后变化逐渐平缓; 破岩效率随钻头转速增大而增加; 破岩效率随冲击载荷的增加变化平缓。据此研制了新型水力旋冲钻井工具。现场试验表明,该工具符合定向水平井“一趟钻”工艺要求,使机械钻速提高56%,使用寿命达150 h,MWD信号正常。 相似文献
5.
为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。 相似文献
6.
Ali AREFNIA Ali DEHGHANBANADAKI Khairul Anuar KASSIM 《Frontiers of Structural and Civil Engineering》2021,15(4):1016
This study investigated the use of recycled tire-derived aggregate (TDA) mixed with kaolin as a method of increasing the ultimate bearing capacity ( UBC) of a strip footing. Thirteen 1g physical modeling tests were prepared in a rigid box of 0.6 m × 0.9 m in plan and 0.6 m in height. During sample preparation, 0%, 20%, 40%, or 60% (by weight) of powdery, shredded, small-sized granular (G 1–4 mm) or large-sized granular (G 5–8 mm) TDA was mixed with the kaolin. A strip footing was then placed on the stabilized kaolin and was caused to fail under stress-controlled conditions to determine the UBC. A rigorous 3D finite element analysis was developed in Optum G-3 to determine the UBC values based on the experimental test results. The experimental results showed that, except for the 20% powdery TDA, the TDA showed an increase in the UBC of the strip footing. When kaolin mixed with 20% G (5–8 mm), the UBC showed a threefold increase over that for the unreinforced case. The test with 20% G (1–4 mm) recorded the highest subgrade modulus. It was observed that the UBC calculated using finite element modeling overestimated the experimental UBC by an average of 9%. 相似文献
7.
Donghai Xu Peng Feng Yang Wang Wanpeng Yang Yu Wang Shaoyan Sun 《American Institute of Chemical Engineers》2022,68(2):e17472
Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone. 相似文献
8.
为了研究径向不耦合条件下爆破效果的影响因素,利用AUTODYN-2D对比不耦合系数、不耦合介质、炸药种类对爆破效果的影响规律。结果表明,与耦合装药相比,径向不耦合装药条件下炮孔压力明显降低。对比水介质和空气介质下的爆破效果可知,水介质不耦合条件下,炸药爆炸能量的传递效率更高。炮孔压力与炸药种类密切相关,TNT产生的炮孔压力最大,但作用时间较短,而ANFO和乳化炸药的作用时间较长。 相似文献
9.
为了保证上海光源X射线干涉光刻光束线的稳定性,减小热变形对实验结果的影响,对X射线干涉光刻光束线的3个关键光学元件——偏转镜、聚焦镜和精密四刀狭缝进行热-结构耦合分析。首先,计算偏转镜、聚焦镜和精密四刀狭缝所承载的功率密度;然后,建立其有限元模型;最后,获得光学元件的温度场和热变形的结果。结果表明,偏转镜和聚焦镜采用间接水冷方式可有效抑制热变形,冷却后的最大面形误差分别为7.2μrad和9.2μrad。精密四刀狭缝未冷却时,刀片组件温度介于271.56~273.27℃,刀口热变形为0.19 mm,直线导轨热变形为0.08 mm;经过铜辫子冷却后,刀片组件温度降至22.24~23.94℃,刀口热变形降至0.2μm,直线导轨热变形降至0.1μm;采用影像法和接触探头法测试后,刀口直线度、平行度和重复精度均满足技术要求。偏转镜、聚焦镜和精密四刀狭缝的热变形通过间接水冷和铜辫子的冷却方式可以得到很大程度的抑制,进而保证光斑质量。 相似文献
10.
针对当前KJS-Y系列降尘器效率低的问题,通过调整叶轮轴向间隙与径向间隙参数,分别对不同安装参数的降尘器进行数值模拟,通过数值模拟分析特定截面压力分布情况,确定了叶轮最佳安装参数,大大提高了降尘器的工作效率,同时降低了设计成本。 相似文献