Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Reconstruction of Mandibular Defect with Porous β-TCP/BMG Artificial Bone

1Introduction Reconstructivesurgeryisoneofthehottestre searchedsubjectsthatdealingwithbonedefects.Thetra ditionalmethodisimplantationoffreshautograftbonebe causeofitsnon immunoreactiveproperty.Butautologousbonewasnotabundantinsomecases.Sowefoundbeta trica…     

常规施工中不容忽视的几个环节

就毛石砌体的拉接处理、现浇混凝土柱、墙拉结筋的留设、砖混结构中构造柱的质量预控等几个环节进行了分析，提出只有在施工中采取必要的措施，才能保证施工质量。     

新型超微晶软磁合金FePCCuMoSi微观结构缺陷的正电子湮没研究

用正电子湮没方法研究了新型超微晶软磁合金的微观结构缺陷，样品选用的是在不同温度下退火的Ｆｅ８１Ｐ１２Ｃ３Ｃｕ１Ｍｏ０．５Ｓｉ２．５合金，结果表明，合金的微观结构构陷大小，密度随退火温度有规律地变化，这种现象可能与非晶的晶化过程有关。     

安徽省长江干堤的几种加固措施

安徽省境内765km的长江干堤，由于均是在原来旧堤的基础上经逐年加高培厚的，修筑时均未按设计要求施工，致使堤身密实度不够，新老堤土之间结合不牢，在汛期高水位时易产生渗漏。20世纪70年代以来，安徽省高度重视对长江干堤渗漏隐患的处理，经过长期的实践，逐渐摸索出一套行之有效的除险加固方法，如锥探灌浆、灭杀白蚁、冲抓套吉、垂直铺塑防渗、粘土铺盖及压渗盖重等处理措施。使长江干堤的渗漏隐患得以基本消除，其具体作法可供类似工程借鉴。     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。     

Plastic deformation of bcc metal thin foils without dislocation

Heavy plastic deformation of fcc metal thin foils to fracture has been found recently to proceed without involving dislocations, and it results in the formation of high density of vacancy clusters. Thin foil specimens of bcc metals such as V and Mo were plastically deformed to fracture in in situ elongation experiments under an electron microscope. Morphology of thinning and fracture was found to be similar to fcc metals, and no dislocation was observed during heavy deformation. Electron diffraction analysis at the tip of a crack during deformation confirmed a large elastic deformation of up to 5%. Unlike in fcc metal thin foil specimens, point defect clusters were not observed near fractured tips. This difference is attributed to the difference in vacancy reaction, though the deformation in bcc metals without dislocation most likely does produce vacancies.     

大尺寸氟化铅晶体的生长

描述了不用高真空条件，在通常的Ｂｒｉｄｇｍａｎ－Ｓｔｏｃｋｂａｒｇｅｒ炉中，用高温下的反应方法，消除了原料及生长炉内残存的Ｏ＾２－及ＯＨ＾－，生长出优质，大尺寸的β－ＰｂＦ２晶体。在晶体生长时，出现的主要问题是在晶体中的针状结构及开裂，但可通过控制条件来解决。     

三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。