Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

Alloying behavior and novel properties of CoCrFeNiMn high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

An equiatomic CoCrFeNiMn high-entropy alloy was synthesized by mechanical alloying (MA) and spark plasma sintering (SPS). During MA, a solid solution with refined microstructure of 10 nm which consists of a FCC phase and a BCC phase was formed. After SPS consolidation, only one FCC phase can be detected in the HEA bulks. The as-sintered bulks exhibit high compressive strength of 1987 MPa. An interesting magnetic transition associated with the structure coarsening and phase transformation was observed during SPS process.     

氮化硅/石墨激光合金化涂层的组织结构与性能研究

为获得金属表面特别是高副接触金属表面含自润滑特性且具有高硬度耐磨特性的功能材料 ,研究了 45 # 钢表面激光合金化氮化硅 /石墨复合涂层的工艺方法、组织特征、界面形态及其形成机制 ,利用光学显微镜、扫描电镜和X射线能谱对所形成合金化层的元素分布和含量进行了分析 ,并对试样硬度进行了测定。结果表明 ,合金化层中元素Fe ,Co ,Si,C分布均匀 ;C含量达到了 15 6 9%,大部分以石墨的形式存在 ,具有一定的自润滑性能 ;但在形成合金化层的温度条件下 ,氮化硅分解严重 ;合金化层硬度提高的主要原因是Si Fe ,Co Fe固溶体的强化作用及高碳马氏体的生成和高硬度碳化物的存在。     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

机械合金化过程中Fe70B30粉末晶粒尺寸和微观应变的研究

用Ｘ射线和电镜研究了Ｆｅ＿（７０）Ｂ＿（３０）粉末经不同时间高能球磨后晶粒尺寸和微观应力的变化。在机械合金化过程中，粉末的Ｘ射线衍射谱的宽度随球磨时间的增加逐渐加宽，这是晶粒细化和内部微观应力共同作用的结果。Ｘ射线衍射结果表明：随着机械合金化的进行，粉末的晶粒尺寸逐渐减小，球磨初期晶粒尺寸下降较快，经１５ｈ球磨，晶粒尺寸为２５ｎｍ，机械合金化进行到一定时间后晶粒尺寸下降缓慢，８０ｈ球磨后晶粒尺寸可达５ｎｍ。在机械合金化过程中球磨所造成的微观应变不大，球磨初期粉末的内应力随球磨时间增加而增加，当粉末粒子尺寸很小时，随球磨的进行粉末中的微观应变显著下降。     

Al-Cu-Fe QUASICRYSTALLINE PHASE FORMATION BY MECHANICAL ALLOYING

Al-Cu-Fe alloys were prepared from elemental powders in a high-energy planetary ball mill. A sequence of solid state reactions resulting in quasicrystal (QC) phase formation takes place during heating of the as-milled powder. These reactions were studied by both differential scanning calorimetry and x-ray diffraction methods. Mechanically alloyed powders were consolidated by cold and hot pressing, as well as by explosive compaction. After annealing at sufficiently high temperatures, the consolidated samples are single-phase QC, except the ones consolidated by explosion. The high reactivity of the as-milled alloys causes the appearance of high porosity of the consolidated samples after the annealing.     

Hydriding and Dehydriding Characteristics of Mechanically Alloyed LaMg_(17) Ni Composite Material

Magnesiumandmagnesiumalloyshavebeenin vestigatedashydrogenstoragematerialsforseveralde cadesbecausefarmorehydrogenbyweightcanbestoredinthemthaninmostoftheothercurrentlyknownhydrogenstoragealloys .Moreover ,thehighnaturalabundanceofMg ,itslightmassandenviron mentalcompatibilitypotentiallymakemagnesiumoneofthemostprospectivecandidatesforfuturehydrogenstoragematerials .Unfortunately ,thepracticalappli cationofMganditsalloyshasbeenlimitedonlytocertainstoragedevicebecauseoftheirpoorhydriding dehydr…     

镁基储氢材料的研究进展

本文回顾和总结了近几十年来，特别是近十年来镁基储氢材料的发展情况，重点综述了机械合金化Mg-Ni2合金体系的研究情况及其近期的进展，从储氢材料成份及配比，制造工艺改进以及材料的组织结构对材料性能的影响等各方面进行一定的分析和归纳，对储氢材料研究中出现的问题以及今后的发展方向都作了探讨。     

Nitrogen addition to iron powder by mechanical alloying

Nitrogen was alloyed into iron (a) by mechanical processing in a nitrogen gas environment, and (b) by mechanically alloying with iron-nitride powders to characterize resulting nano-structure and nitrogen distribution. Although the infused nitrogen concentration was significantly greater than the thermodynamic equilibrium solubility of iron, no nitrides formed, even for nitrogen concentrations as high as 4.1 wt.% However, a bctFe phase did form. Lattice expansion calculations indicate that the sum of the interstitial bcc-Fe and bctFe nitrogen concentrations was significantly less than the total measured nitrogen concentration. A considerable portion of the mechanically infused nitrogen was determined to be associated with nanograin boundaries.     

发电机用DJL350磁极钢板的开发与应用

本文论述了高强度冷轧磁极板的试制性研究，应用性研究及在开生桥机组上的实施。通过与国外材料的对比，研究了材料的化学成分、力学性能、磁性能、金相组织及其与性能的关系。并对其实际应用效果进行了分析总结。