Influences of assembly pressure and flow channel size on performances of proton exchange membrane fuel cells based on a multi-model

In this work, assembly pressure and flow channel size on proton exchange membrane fuel cell performance are optimized by means of a multi-model. Based on stress-strain data of the SGL-22BB GDL obtained from its initial compression experiments, Young's modulus with different ranges of assembly pressure fits well through modeling. A mechanical model is established to analyze influences of assembly pressure on various gas diffusion layer parameters. Moreover, a CFD calculation model with different assembly pressures, channel width, and channel depth are established to calculate PEMFC performances. Furthermore, a BP neural network model is utilized to explore optimal combination of assembly pressure, channel width and channel depth. Finally, the CFD model is used to validate effect of size optimization on PEMFC performance. Results indicate that gap change of GDL below bipolar ribs is more remarkable than that below channels under action of the assembly pressure, making liquid water easily transported under high porosity, which is conducive to liquid water to the channels, reduces the accumulation of liquid water under the ribs, and enhances water removal in the PEMFC. Affected by the assembly force, change of GDL porosity affects its diffusion rate, permeability and other parameters, which is not conducive to mass transfer in GDL. Optimizing the depth and different dimensions through width of the flow field can effectively compensate for this effect. Therefore, the PEMFC performance can be enhanced through the comprehensive optimization of the assembly force, flow channel width and flow channel depth. The optimal parameter is obtained when assembly pressure, channel width and channel depth are set as 0.6 MPa, 0.8 mm, and 0.8 mm, respectively. The parameter optimization enhances the mass transfer, impedance, and electrochemical characteristics of PEMFC. Besides, it effectively enhances the quality transfer efficiency inside GDL, prevents flooding, and reduces concentration loss and ohmic loss.     

Applications of sketches in network traffic measurement: A survey

Accurate and timely network traffic measurement is essential for network status monitoring, network fault analysis, network intrusion detection, and network security management. With the rapid development of the network, massive network traffic brings severe challenges to network traffic measurement. However, existing measurement methods suffer from many limitations for effectively recording and accurately analyzing big-volume traffic. Recently, sketches, a family of probabilistic data structures that employ hashing technology for summarizing traffic data, have been widely used to solve these problems. However, current literature still lacks a thorough review on sketch-based traffic measurement methods to offer a comprehensive insight on how to apply sketches for fulfilling various traffic measurement tasks. In this paper, we provide a detailed and comprehensive review on the applications of sketches in network traffic measurement. To this end, we classify the network traffic measurement tasks into four categories based on the target of traffic measurement, namely cardinality estimation, flow size estimation, change anomaly detection, and persistent spreader identification. First, we briefly introduce these four types of traffic measurement tasks and discuss the advantages of applying sketches. Then, we propose a series of requirements with regard to the applications of sketches in network traffic measurement. After that, we perform a fine-grained classification for each sketch-based measurement category according to the technologies applied on sketches. During the review, we evaluate the performance, advantages and disadvantages of current sketch-based traffic measurement methods based on the proposed requirements. Through the thorough review, we gain a number of valuable implications that can guide us to choose and design proper traffic measurement methods based on sketches. We also review a number of general sketches that are highly expected in modern network systems to simultaneously perform multiple traffic measurement tasks and discuss their performance based on the proposed requirements. Finally, through our serious review, we summarize a number of open issues and identify several promising research directions.     

三维石墨烯-碳纳米管/水泥净浆的压敏性能

为了探索三维石墨烯-碳纳米管(G-CNTs)/水泥净浆的压敏性能,采用四电极法研究了荷载作用下GCNTs/水泥净浆的电阻率变化,并分析不同G-CNTs掺量、加载幅度、加载速度以及恒定荷载对电阻率变化的影响。研究表明:随着G-CNTs掺量的增加,电阻率呈先减小后稳定的变化趋势,在G-CNTs掺量由0.2wt%增加至1.6wt%时,电阻率下降51.8%;电阻率与温度呈负相关;G-CNTs掺量高于0.8wt%时可以显著提高水泥净浆的压敏性能,且电阻率变化率与应力应变有明显的对应关系,1.2wt%G-CNTs掺量下试件的应力灵敏系数和应变灵敏系数分别为2.3%/MPa和291;G-CNTs/水泥净浆电阻率变化率幅值随着加载幅度增大而相应增加,其电阻率变化率曲线在不同加载速度以及恒定荷载作用下均与应力-应变曲线一一对应,具有良好的压敏特性。     

Comparative analysis of inbreeding parameters and runs of homozygosity islands in 2 Italian autochthonous cattle breeds mainly raised in the Parmigiano-Reggiano cheese production region

Reggiana and Modenese are autochthonous cattle breeds, reared in the North of Italy, that can be mainly distinguished for their standard coat color (Reggiana is red, whereas Modenese is white with some pale gray shades). Almost all milk produced by these breeds is transformed into 2 mono-breed branded Parmigiano-Reggiano cheeses, from which farmers receive the economic incomes needed for the sustainable conservation of these animal genetic resources. After the setting up of their herd books in 1960s, these breeds experienced a strong reduction in the population size that was subsequently reverted starting in the 1990s (Reggiana) or more recently (Modenese) reaching at present a total of about 2,800 and 500 registered cows, respectively. Due to the small population size of these breeds, inbreeding is a very important cause of concern for their conservation programs. Inbreeding is traditionally estimated using pedigree data, which are summarized in an inbreeding coefficient calculated at the individual level (F_PED). However, incompleteness of pedigree information and registration errors can affect the effectiveness of conservation strategies. High-throughput SNP genotyping platforms allow investigation of inbreeding using genome information that can overcome the limits of pedigree data. Several approaches have been proposed to estimate genomic inbreeding, with the use of runs of homozygosity (ROH) considered to be the more appropriate. In this study, several pedigree and genomic inbreeding parameters, calculated using the whole herd book populations or considering genotyping information (GeneSeek GGP Bovine 150K) from 1,684 Reggiana cattle and 323 Modenese cattle, were compared. Average inbreeding values per year were used to calculate effective population size. Reggiana breed had generally lower genomic inbreeding values than Modenese breed. The low correlation between pedigree-based and genomic-based parameters (ranging from 0.187 to 0.195 and 0.319 to 0.323 in the Reggiana and Modenese breeds, respectively) reflected the common problems of local populations in which pedigree records are not complete. The high proportion of short ROH over the total number of ROH indicates no major recent inbreeding events in both breeds. ROH islands spread over the genome of the 2 breeds (15 in Reggiana and 14 in Modenese) identified several signatures of selection. Some of these included genes affecting milk production traits, stature, body conformation traits (with a main ROH island in both breeds on BTA6 containing the ABCG2, NCAPG, and LCORL genes) and coat color (on BTA13 in Modenese containing the ASIP gene). In conclusion, this work provides an extensive comparative analysis of pedigree and genomic inbreeding parameters and relevant genomic information that will be useful in the conservation strategies of these 2 iconic local cattle breeds.     

Effects of the Anti-Tumorigenic Agent AT101 on Human Glioblastoma Cells in the Microenvironmental Glioma Stem Cell Niche

Glioblastoma (GBM) is a barely treatable disease due to its profound chemoresistance. A distinct inter- and intratumoral heterogeneity reflected by specialized microenvironmental niches and different tumor cell subpopulations allows GBMs to evade therapy regimens. Thus, there is an urgent need to develop alternative treatment strategies. A promising candidate for the treatment of GBMs is AT101, the R(-) enantiomer of gossypol. The present study evaluates the effects of AT101, alone or in combination with temozolomide (TMZ), in a microenvironmental glioma stem cell niche model of two GBM cell lines (U251MG and U87MG). AT101 was found to induce strong cytotoxic effects on U251MG and U87MG stem-like cells in comparison to the respective native cells. Moreover, a higher sensitivity against treatment with AT101 was observed upon incubation of native cells with a stem-like cell-conditioned medium. This higher sensitivity was reflected by a specific inhibitory influence on the p-p42/44 signaling pathway. Further, the expression of CXCR7 and the interleukin-6 receptor was significantly regulated upon these stimulatory conditions. Since tumor stem-like cells are known to mediate the development of tumor recurrences and were observed to strongly respond to the AT101 treatment, this might represent a promising approach to prevent the development of GBM recurrences.     

高岭土性质对催化裂化催化剂性能的影响

采用X射线荧光分析仪、X射线衍射仪、N2物理吸附仪、场发射扫描电子显微镜等仪器表征了苏州、广西和美国佐治亚州3个产地的高岭土，并以此3种高岭土为原料制备了模型催化裂化（FCC）催化剂，在ACE评价装置上对比了模型催化剂的反应性能。结果表明:苏州及广西高岭土主要组分为高岭石，佐治亚高岭土主要组分为地开石及珍珠陶土；苏州高岭土呈片状，还含有少量棒状颗粒；广西高岭土呈多层片状，晶粒粒径较大；佐治亚高岭土呈薄片状，晶粒粒径较小；3种高岭土制备的模型催化剂反应活性、Na2O及RE2O3质量分数相近；广西高岭土制备的模型催化剂具有最大的孔体积和磨损指数，但比表面积最小，具有较强的重油转化能力，其目标产物（液化气+汽油）和副产物（干气+焦炭）收率都高于苏州、佐治亚高岭土制备的催化剂的。     

减水剂类型对赤泥—矿渣基地聚物注浆材料性能的影响及机理研究

针对赤泥等固体废弃物对环境危害性大且利用率低等问题,以碱激发赤泥-矿渣基地聚物注浆材料为 研究对象,研究了不同掺量的聚羧酸(PA)减水剂、醛酮缩合物(AKC)减水剂和萘系(N)减水剂对材料凝结时间、流动 性及强度等的影响,并通过 XRD、傅里叶红外光谱及 SEM 等设备对减水剂的作用机理进行研究。 结果表明:减水剂增 强了材料的流动性但降低了材料的剪切应力;N 和 PA 减水剂能缩短材料的凝结时间,但 AKC 减水剂会延长材料的凝 结时间;N 和 AKC 减水剂能提高材料的强度,但 PA 减水剂会降低材料的强度;N 减水剂对材料的综合性能提升效果 更加明显,其最优掺量为 0. 7%;减水剂对赤泥-矿渣基地聚物性能提升的作用机理主要是促进地聚合物凝胶的形成。 研究成果为拓展赤泥在工程上的使用途径和效率提供了理论指导。     

High-surface-area mesoporous silica-yttria-zirconia ceramic materials prepared by coprecipitation method ― the role of silicon

A high surface area is one of desired properties for yttria-zirconia (Y₂O₃–ZrO₂) ceramic materials given their catalytic applications. The objective of this study is to develop high-surface-area Y₂O₃–ZrO₂ materials by silicon (Si) modification and investigate the role of Si. Si-modified yttrium-zirconium hydroxides were prepared via a one-step precipitation process and calcined at 800 or 950 °C to form Si-modified Y₂O₃–ZrO₂ (denoted as SiO₂–Y₂O₃–ZrO₂) materials containing 0-20 wt% Si as SiO₂. These hydroxides or materials were characterized by ²⁹Si NMR, XPS, TG-DSC, XRD, UV Raman, TEM, and N₂ physisorption measurements. Si species uniformly distributed in the hydroxides tended to be enriched on the material surface at high temperatures. These Si species dominated by the silicates blocked the migration of Y and Zr atoms, which resisted the crystallite growth of Y₂O₃–ZrO₂ components and reduced their crystallite size. Therefore, the SiO₂–Y₂O₃–ZrO₂ possessed a surface area of 59-112 m²/g after calcination at 950 °C for 9 h, which was significantly higher than that of the Y₂O₃–ZrO₂ (23 m²/g). This study may stimulate ideas for developing high-surface-area crystalline ceramic materials calcined at high temperatures.