Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

黑匣子高温测试仪的开发

采用物质的相变吸热原理，可以将高温环境传人保温箱的热量重新排回至高温环境，有效地提高了保温箱的抗高温能力，并对保温箱的隔热性能做了简单的理论推算和测温反向试验。温度测试仪选用超低功耗CPU，具有体积小、耗电少的优点，使黑匣子高温测试仪在运行过程中具有很好的安全可靠性。     

基于单片机加压控制的PCD复合片真空扩散焊接

文章针对普通钎焊的聚晶金刚石钻头剪切强度不高，提出了采用单片机加压控制的PCD复合片真空扩散焊接的设计思想，在对原真空扩散焊机液压改造的基础上给出如何由单片机控制加压的电路和程序流程设计。实际应用表明，该技术经济实用，有较好的经济效益。     

原油常减压装置节能技术

由于常减压装置消耗能量约占炼油厂总用能的25％～30％，已成为炼油厂中消耗量最大的装置，因此，我国各炼油厂对常减压装置进行以降低能耗为中心的技术改造就显得十分必要。详细介绍了适用于常减压装置节能的新工艺、新设备以及优化操作。工艺方面主要有采用过滤脱盐新技术对原油进行深度脱盐、采用强化蒸馏新工艺提高原油蒸馏拔出率、优化产出、增产柴油；设备方面主要使用规整填料和新型塔板改善分馏塔分馏效率、使用新型燃烧器提高加热炉效率、使用新型换热器提高热回收率、采用变频技术降低装置电耗；优化操作方面主要有利用计算机进行监控与管理和改善操作条件。最后对国内原油常减压装置节能改造提出了一些建议，以供炼油企业在进行原油常减压装置改造时参考。     

Evaluation of Atmospheric and Vacuum Residues Using Molecular Distillation and Optimization

The term atmospheric residue describes the material at the bottom of the atmospheric distillation tower having a lower boiling point limit of about 340°C; the term vacuum residue (heavy petroleum fractions) refers to the bottom of the vacuum distillation, which has an atmospheric equivalent boiling point (AEBP) above 540°C. In this work, the objective is to evaluate the behavior of different kinds of Brazilian atmospheric and vacuum residues using molecular distillation. The Falling Film Molecular Distillator was used. For the results obtained through this process, a significant range of temperature can be explored avoiding the thermal decomposition of the material. So these results are very important to the refinery decisions and improvements. The Experimental Factorial Design results showed that the temperature has more influence on the process than the feed flow rate, when a higher percentage of distillate is required.     

基于数字机顶盒的电子选单的设计和实现

基于CATV和PSTN的VOD多媒体数字机顶盒，提出了几种实现双向通信以完成电子节目指南的设计方案，对各种方案的优缺点进行了详细的讨论，并介绍了所采用方案的实现方法。     

化肥厂合成气及重整氢真空变压吸附制取高纯度氢气

从设计、生产操作和经济效益3个方面阐述了以化肥厂合成气及重氢为原料，通过真空变压吸附（VPSA）装置制取高纯度氢的过程。工业应用结果表明，该制氢工艺是一项操作简便灵活，制氢费用较低的工艺路线。VPSA装置技术和设计上的特点能够保证大的操作弹性、高的产品氢纯度和较高的氢气回收率。在36％－51％的低限负荷下，通过适当调整吸附时间，可获得纯度99％的氢气产品，89％－92％的氢气回收率。     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

法国产CT4型横拼双金属专用真空电子束焊机原理与构造

试述法国TECHMETA公司产的CT4型横拼双金属专用真空电子束焊机原理与构造，其中主要阐述电子枪控制电路板的原理。     

高真空条件下网状泡沫放气量的测试

利用航天工业行业标准及测试设备对一定真空度条件下的聚胺脂网状泡沫在常温及加温两种不同工况时的出气情况进行测试；对两者的放气量进行比较；对放气机理进行分析探讨。此工作对高真空连续卷绕网状泡沫镀镍设备的真空系统配置具有一定的指导意义。