Microstructure,wear and corrosion characteristics of multiple-reinforced (SiC–B4C–Al2O3) Al matrix composites produced by liquid metal infiltration

In this study, AA7075 aluminum matrix composites reinforced with the combination of SiC, Al₂O₃, and B₄C particles were fabricated by the liquid metal infiltration method. The effects of the relative ratio of B₄C and Al₂O₃ particles on the microstructural, wear, and corrosion features of the composite samples were analyzed using XRD, light metal microscopy, SEM, EDS, Brinell hardness, ball-on-disc type tribometer, and potentiodynamic polarization devices. It was determined that infiltration occurred more successfully, and homogenously distributed particles with reduced porosity were obtained as the amount of Al₂O₃ increased. Worn surface studies revealed that the specimens were predominantly worn by abrasion and adhesion. The increase in B₄C/Al₂O₃ ratio caused a decrease in the hardness and wear strength, whereas it increased the corrosion resistance.     

5A06-O aluminium–magnesium alloy sheet warm hydroforming and optimization of process parameters

The uniaxial tensile test of the 5A06-O aluminium–magnesium (Al–Mg) alloy sheet was performed in the temperature range of 20–300 °C to obtain the true stress–true strain curves at different temperatures and strain rates. The constitutive model of 5A06-O Al–Mg alloy sheet with the temperature range from 150 to 300°C was established. Based on the test results, a unique finite element simulation platform for warm hydroforming of 5A06-O Al–Mg alloy was set up using the general finite element software MSC.Marc to simulate warm hydroforming of classic specimen, and a coupled thermo-mechanical finite element model for warm hydroforming of cylindrical cup was built up. Combined with the experiment, the influence of the temperature field distribution and loading conditions on the sheet formability was studied. The results show that the non-isothermal temperature distribution conditions can significantly improve the forming performance of the material. As the temperature increases, the impact of the punching speed on the forming becomes particularly obvious; the optimal values of the fluid pressure and blank holder force required for forming are reduced.     

Corrosion behavior of under‐, peak‐, and over‐aged 6063 alloy: A comparative study

The mechanical property of age‐hardenable Al‐alloys is governed by the state of ageing, which determines the microstructure and consequently, their corrosion behavior which is a vital aspect for a number of applications. This article presents a comparative assessment of corrosion behavior of under‐, peak‐ and over‐aged Al‐Mg‐Si alloy. Corrosion characteristics have been determined via immersion tests in 0.1 M ortho‐phosphoric acid solution and intergranular corrosion (IGC) tests. Corroded surfaces are examined by field emission scanning electron micrographs‐energy dispersive spectroscopy and 3D optical profilometer. The obtained results reveal that the corrosion rate at a specific immersion time as well as the depth of IGC increases in the order for under‐, peak‐, and over‐aged states. Irrespective of the state of ageing, corrosion loss increases linearly but the rate of corrosion decreases rapidly with increasing immersion time. The dominant mode of corrosion in under‐aged alloy is identified as localized pitting, while peak‐aged is highly susceptible to IGC in contrast extensive pitting corrosion is observed for over‐aged alloy. The observed differences in corrosion behavior are explained considering characteristics of precipitates. Formation of β (Mg₂Si) in case of over‐aged alloy and presence of inclusions like AlFeMnSi particles are found to accelerate pitting corrosion.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Efficiency and effectiveness enhancement of an intercooler of two‐stage air compressor by low‐cost Al2O3/water nanofluids

The present study was aimed to utilize low‐cost alumina (Al₂O₃) nanoparticles for improving the heat transfer behavior in an intercooler of two‐stage air compressor. Experimental investigation was carried out with three different volume concentrations of 0.5%, 0.75%, and 1.0% Al₂O₃/water nanofluids to assess the performance of the intercooler, that is, counterflow heat exchanger at different loads. Thermal properties such as thermal conductivity and overall heat transfer coefficient of nanofluid increased substantially with increasing concentration of Al₂O₃ nanoparticles. Specific heat capacity of nanofluids were lower than base water. The intercooler performance parameters such as effectiveness and efficiency improved appreciably with the employment of nanofluid. The efficiency increased by about 6.1% with maximum concentration of nanofluid, that is, 1% at 3‐bar compressor load. It is concluded from the study that high concentration of Al₂O₃ nanoparticles dispersion in water would offer better heat transfer performance of the intercooler.     

Unraveling the effect of alumina-supported Y- doped ceria composition and method of preparation on the WGS activity of gold catalysts

The demands for high-purity hydrogen required in fuel-cell applications impose new goals and challenges for design of well performing water-gas shift (WGS) catalysts. Gold-based catalysts have exhibited high activity in the WGS reaction at low temperature. Preparation of appropriate and economically viable supports with complex composition by various synthesis procedures is an attractive approach to WGS performance improvement. The effect of two different preparation methods (wet impregnation or mechanical mixing) and ceria content (10, 20 or 30 wt%) on textural, structural, surface and reductive properties and WGS activity of gold catalysts was studied. Additionally, the role of Y₂O₃ as a promoter of ceria was examined. Long-term stability test was carried out at 260 °C over the most active catalyst. The composition of the best performing sample (composed of about 70 wt% alumina), prepared by mechanical mixing, was considered promising in case of practical applications because of its cost efficiency. The combination of gold nanoparticles and alumina supported Y-doped ceria proved an advantageous approach for developing new catalytic formulations with high effectiveness in clean hydrogen production.     

Al、Mo含量对铸造钛合金力学性能的影响

运用正交实验 ,考察了Al、Mo含量对Ti Al Mo 1Zr系铸造钛合金力学性能的影响。试验结果表明 :随Al、Mo含量提高 ,铸造合金的强度增加 ,塑性和冲击韧性降低 ,但Al、Mo的交互作用却使合金塑性提高 ,强度和冲击韧性降低     

凝胶成型法制备加氢催化剂载体的研究与工业化生产

采用凝胶成型法制备加氢催化剂载体，并进行了工业放大试验。通过BET、NH3-TPD、H2-TPR等表征手段及实际的加氢反应性能评价对凝胶成型法制备的载体及加氢催化剂与常规方法进行对比分析，结果表明，采用凝胶成型法所制得的载体及催化剂均具有较高的孔体积和比表面积、较低的堆密度，其机械强度可满足工业要求，总酸量及中强酸酸量得到提升，催化剂活性组分与载体强结合力得到削弱，金属利用率提高，应用性能明显优于传统方法制备的加氢催化剂载体。通过该方法完成了加氢催化剂载体的工业生产，所生产的载体应用于天津院THDS-3加氢精制催化剂取得了良好的工业应用效果。