Analysis of suitability of TPP ash-slag waste as materials for hydrogen fuel storage

The current trends in energy were described, the main of which is the use of alternative energy sources, especially hydrogen. The most common methods of hydrogen accumulation were proposed: accumulation of compressed gaseous hydrogen in high-pressure tanks; accumulation of liquid hydrogen in cryogenic tanks; storing hydrogen in a chemically bound state; accumulation of gaseous hydrogen in carriers with a high specific surface area. Based on the combination of advantages and disadvantages, the most promising methods of accumulation were selected: storage of liquid hydrogen and storage of hydrogen in carriers with a high specific surface area. The main requirement for materials for hydrogen storage by these methods was revealed – a high specific surface area. Prospects for the development of waste-free low-emission technologies due to the recycling of secondary raw materials and the development of low-temperature technologies for the synthesis of functional and structural materials were substantiated. The applicability of large-scale ash and slag waste from coal-fired thermal power plants as a raw material for obtaining materials by low-temperature technologies was shown. The traditional ways of using ash and slag waste as a raw material, active additive and filler in the production of cements were described. Modern technologies for the production of innovative materials with a unique set of properties were presented, namely carbon nanotubes, silica aerogel and geopolymer materials. The prospect of using geopolymer matrices as a precursor for the synthesis of a number of materials was described; the most promising type of materials was selected – geopolymer foams, which are mainly used as sorbents for purifying liquids and gases or accumulating target products, as well as heat-insulating materials. The possibility of obtaining products of any shape and size on the basis of geopolymer matrices without high-temperature processing was shown. The special efficiency of the development of the technology of porous granules and powders obtained from a geopolymer precursor using various methods was substantiated. The obtained granules can be used in the following hydrogen storage technologies: direct accumulation of hydrogen in porous granules; creation of insulating layers for liquid hydrogen storage units.     

Polyaniline encapsulated Ti-MOF/CoS for efficient photocatalytic hydrogen evolution

We report the study of conductive polyaniline (PANI) chain embedded Ti-MOF functionalized with CoS as a cocatalyst for hydrogen evolution reaction (HER) application. The post synthetically modified hybrid photocatalyst PANI/Ti-MOF/CoS greatly influences the redox and e^? ? h⁺ separation process and exhibits an impressive rate of HER (～1322 μmol h^?1g^?1), suppressing the pristine Ti-MOF (～62 μmol h^?1g^?1) with apparent quantum yield (AQY) of ～3.2 and transient current response of ～46.4 μA cm^?2. In this system, Ti-MOF provides the circulation of Ti³⁺ and Ti⁴⁺ to the reaction of photocatalytic H₂ generation, where the additional PANI and CoS amended the performance of H₂ production through electron enrichment and thereby improving the stability and integrity of Ti-MOF. The Electrochemical studies demonstrated increased photocurrent by interweaving Ti-MOF crystal with PANI through cation-π interaction thereby enhancing interface connection and then promoting electron transfers. The charge dynamics revealed the initial charge transfer from photoexcited PANI to encapsulated MOF framework to boost the photocatalytic performance of the system. Further, the electron movement at the Ti-MOF/CoS interface is investigated through work function and electrochemical potential of electrons (Fermi level). DFT results demonstrate the importance of CoS in improving the photocatalytic performance of hybrid Ti-MOF catalyst, which leads to superior catalytic behaviour. These results establish that the encapsulation of catalytic active sites inside MOFs with desirable energy band gaps would be an ideal choice for the production of solar fuels.     

Electrowetting-Assisted Generation of Ultrastable High Charge Densities in Composite Silicon Oxide–Fluoropolymer Electret Samples for Electric Nanogenerators

Electric nanogenerators that directly convert the energy of moving drops into electrical signals require hydrophobic substrates with a high density of static electric charge that is stable in “harsh environments” created by continued exposure to potentially saline water. The recently proposed charge-trapping electric generators (CTEGs) that rely on stacked inorganic oxide–fluoropolymer (FP) composite electrets charged by homogeneous electrowetting-assisted charge injection (h-EWCI) seem to solve both problems, yet the reasons for this success have remained elusive. Here, systematic measurements at variable oxide and FP thickness, charging voltage, and charging time and thermal annealing up to 230 °C are reported, leading to a consistent model of the charging process. It is found to be controlled by an energy barrier at the water-FP interface, followed by trapping at the FP-oxide interface. Protection by the FP layer prevents charge densities up to −1.7 mC m⁻² from degrading and the dielectric strength of SiO₂ enables charge decay times up to 48 h at 230 °C, suggesting lifetimes against thermally activated discharging of thousands of years at room temperature. Combining high dielectric strength oxides and weaker FP top coatings with electrically controlled charging provides a new paradigm for developing ultrastable electrets for applications in energy harvesting and beyond.     

Colossal dielectric response and relaxation behavior in novel system of Zr4+ and Nb5+ co-substituted CaCu3Ti4O12 ceramics

In this work, we developed a novel system of isovalent Zr⁴⁺ and donor Nb⁵⁺ co-doped CaCu₃Ti₄O₁₂ (CCTO) ceramics to enhance dielectric response. The influences of Zr⁴⁺ and Nb⁵⁺ co-substituting on the colossal dielectric response and relaxation behavior of the CCTO ceramics fabricated by a conventional solid-phase synthesis method were investigated methodically. Co-doping of Zr⁴⁺ and Nb⁵⁺ ions leads to a significant reduction in grain size for the CCTO ceramics sintered at 1060 °C for 10 h. XRD and Raman results of the CaCu₃Ti_3.8-xZr_xNb_0.2O₁₂ (CCTZNO) ceramics show a cubic perovskite structure with space group Im-3. The first principle calculation result exhibits a better thermodynamic stability of the CCTO structure co-doped with Zr⁴⁺ and Nb⁵⁺ ions than that of single-doped with Zr⁴⁺ or Nb⁵⁺ ion. Interestingly, the CCTZNO ceramics exhibit greatly improved dielectric constant (~10⁵) at a frequency range of 10²–10⁵ Hz and at a temperature range of 20–210 °C, indicating a giant dielectric response within broader frequency and temperature ranges. The dielectric properties of CCTZNO ceramics were analyzed from the viewpoints of defect-dipole effect and internal barrier layer capacitance (IBLC) model. Accordingly, the immensely enhanced dielectric response is primarily ascribed to the complex defect dipoles associated with oxygen vacancies by co-doping Zr⁴⁺ and Nb⁵⁺ ions into CCTO structure. In addition, the obvious dielectric relaxation behavior has been found in CCTZNO ceramics, and the relaxation process in middle frequency regions is attributed to the grain boundary response confirmed by complex impedance spectroscopy and electric modulus.     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

济阳坳陷下古生界潜山油气藏特征及成藏模式

济阳坳陷下古生界潜山具有多样性、复杂性的特点，潜山差异性的形成演化、油气成藏主控因素和控藏模式不明确，严重制约了该区潜山油气勘探。在潜山分类的基础上，综合利用系统恢复、分类对比和典型解剖等方法，揭示了济阳坳陷下古生界不同类型潜山的形成演化过程和油气成藏主控因素差异性，分类建立了油气成藏模式。研究表明，济阳坳陷下古生界主要发育高位新盖侵蚀残丘潜山、中位古盖拉张断块潜山、中位新古盖拉张剪切断块潜山、中位中古盖挤压拉张断块潜山和低位古盖拉张滑脱断块潜山5种潜山类型。不同类型潜山的形成演化和油气成藏各具特色，其中，高位新盖侵蚀残丘潜山的发育受隆升、侵蚀作用控制，油气成藏主要受控于油源和盖层条件，表现为"单向供烃、砂体-不整合岩溶体联合输导、残丘控藏"的成藏模式；中位古盖拉张断块潜山的发育受掀斜、断裂作用控制，油气成藏主要受控于储集条件，表现为"单向供烃、顺向断层输导、反向断层控藏"的成藏模式；中位新古盖拉张剪切断块潜山的发育受反转、翘倾和走滑切割作用控制，油气成藏主要受控于输导条件，表现为"多源供烃、断溶体立体输导、断裂控藏"的成藏模式；中位中古盖挤压拉张断块潜山的形成受强烈挤压、拉张滑脱作用控制，油气成藏主要受控于储集条件，表现为"多源供烃、断缝体输导、断褶控藏"的成藏模式；低位古盖拉张滑脱断块潜山的形成受强烈拉张滑脱作用控制，油气成藏主要受控于输导条件，表现为"顶部供烃、断缝体输导、断裂控藏"的成藏模式。     

Enhance cycling performance of LiMn2O4 cathode by Sr2+ and Cr3+ doping

Spinel LiSr_0·1Cr_0·1Mn_1·8O₄ was synthesised by high temperature solid state method in order to enhance the electrochemical performance. The LiSr_0·1Cr_0·1Mn_1·8O₄ (LSCMO) materials were characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The XRD and SEM studies confirm that LSCMO had spinel crystal structure with a space group of Fd3m, and the particle of LSCMO shows irregular shape. The cyclic voltammetry data illustrated that the heavy current charge–discharge performance of LMO was improved by Sr²⁺ and Cr³⁺ doping. The galvanostatic charge–discharge of LSCMO cathode materials was measured at 1, 5, 10 and 20 C. The results indicated that LSCMO improved the capacity retention.     

An agile model for the eco-design of electric vehicle Li-ion batteries

Numerous design choices need to be made at several levels when designing high-tech products: technology, processes, architecture, components, materials… and these choices need to be made in relation to the product life cycle with the corresponding experts for each stage of the life cycle. At the same time, to ensure product sustainability, a specific focus on the future potential environmental impacts is highly recommended. In this research, an agile model is proposed to help designers make decisions while monitoring environmental performance indicators of high-tech solutions. The concept of Critical Product Life Cycle Parameters had to be introduced to facilitate the eco-design of the final product. The approach is illustrated by the Electric Vehicle Li-Ion Batteries case study.     

径向不耦合装药爆破效果的数值研究

为了研究径向不耦合条件下爆破效果的影响因素,利用AUTODYN-2D对比不耦合系数、不耦合介质、炸药种类对爆破效果的影响规律。结果表明,与耦合装药相比,径向不耦合装药条件下炮孔压力明显降低。对比水介质和空气介质下的爆破效果可知,水介质不耦合条件下,炸药爆炸能量的传递效率更高。炮孔压力与炸药种类密切相关,TNT产生的炮孔压力最大,但作用时间较短,而ANFO和乳化炸药的作用时间较长。     

Assessing the cost-effectiveness of electric vehicles in European countries using integrated modeling

Electric vehicles (EVs) are considered alternatives to internal combustion engines due to their energy efficiency and contribution to CO₂ mitigation. The adoption of EVs depends on consumer preferences, including cost, social status and driving habits, although it is agreed that current and expected costs play a major role. We use a partial equilibrium model that minimizes total energy system costs to assess whether EVs can be a cost-effective option for the consumers of each EU27 member state up to 2050, focusing on the impact of different vehicle investment costs and CO₂ mitigation targets. We found that for an EU-wide greenhouse gas emission reduction cap of 40% and 70% by 2050 vis-à-vis 1990 emissions, battery electric vehicles (BEVs) are cost-effective in the EU only by 2030 and only if their costs are 30% lower than currently expected. At the EU level, vehicle costs and the capability to deliver both short- and long-distance mobility are the main drivers of BEV deployment. Other drivers include each state’s national mobility patterns and the cost-effectiveness of alternative mitigation options, both in the transport sector, such as plug-in hybrid electric vehicles (PHEVs) or biofuels, and in other sectors, such as renewable electricity.