CHA无机凝胶体系的研究及应用

过去低渗油藏调剖，注入性和堵塞性很难统一，新研制的CHA无机凝胶体系是一种易注入、堵塞能力强的调剖剂，而且成胶时间在一定范围内可控。研究了配比、温度对CHA无机凝胶体系成胶时间的影响，成胶前的注入性，成胶后在高温高盐条件下的堵塞能力，得到了可应用于现场的CHA无机凝胶体系。该调剖剂在濮城油田沙三段和文卫结合部等高温、高盐低渗油藏应用后，取得了很好的效果。     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

水库调水调沙回顾与展望--兼论小浪底水库运用方式研究

作者简要回顾了三门峡、恒山水库调度方式和小浪底工程设计、“八五”攻关和专题研究之运用方式以及碛口、三门峡、小浪底水库联合调度方式等。提出小浪底水库调度应坚持“多年调节泥沙 ,相机排沙”运用方式 ;调控库容应大一些 ,同时要有灵活性 ;充分利用天然大水过程排沙 ,必要时也可相机造峰 ;注重水库联合调水调沙运用及有关技术问题研究     

DETECTOR: A knowledge-based system for injection molding diagnostics

A knowledge-based system (KBS) for diagnosis of multiple defects in injection molding is presented. The general scheme for knowledge representation based on fuzzy set theory has been shown useful in representing inexact and incomplete information for developing the KBS. An optimality criterion is created for selecting a simple and best cover to explain the given problem. An efficient search algorithm for finding such cover is also discussed.     

用于VLSI的SiO_xN_y薄膜的界面陷阱

采用雪崩热电子注入技术研究了用于VLSI的快速热氮化的SiO_xN_y薄膜界面陷阱。给出这种薄介质膜禁带中央界面陷阱密度随氮化时间的变化关系,观察到这种薄膜存在着不同类型的密度悬殊很大的电子陷阱。指出雪崩热电子注入过程中在Si/SiO_xN_y界面上产生两类性质不同的快界面态陷阱,并给出这两种陷阱在禁带中能级位置及密度大小关系;同时还给出禁带中央界面陷阱密度随雪崩注入剂量呈现弱“N”形变化关系,并对实验结果进行了讨论。     

双活塞杆油缸在注塑机中的新应用

采用双活塞杆油缸注射装置，开发了一种新型注塑成型机，使用效果表明：采用该装置能提高功效，降低成本，节约能源。     

聚碳酸酯的吹塑成型

简介聚碳酸酯吹塑容器的特性与用途,着重分析其吹塑(包括挤出吹塑、共挤吹塑和注射吹塑)成型的机械(螺杆、机筒、型坯机头与吹塑模具)设计要点及工艺条件。     

新型液晶PVDF合金的研究

本文系统地研究了液晶聚合物(LCP)与PVDF合金共混体系的组成及加工工艺条件对共混物制件性能的影响。并用SEM观察了合金的形态结构。结果表明:在液晶含量10%左右时,加工温度为210℃,合金的拉伸强度最高,磨耗量最低,体系分散均匀并形成了较多的微纤结构。     

注塑模温度场的计算机模拟

本文运用有限元法，采用二次等参单元，对注塑模二维非稳态温度场进行了数值分析，推导了有限元数值求解方程并研制了有限元求解程序软件。实例所得温度场等温线与实验所得结果基本相符，验证了计算机求解的可靠性。通过计算机模拟分析，可了解各瞬时模具温度场的分布状态，观察模具体能否使塑件均匀冷却，如不合理，可通过改变冷却管道参数，达到温度场均匀一致，从而提高塑件质量。通过程序运转，根据塑件的热定型温度，可以预知最短冷却时间，从而缩短冷却周期，提高塑件生产率