Microstructures and properties of nickel-titanium carbide composites fabricated by laser cladding

In this work, Ni/TiC composites were synthesized by the laser cladding technique (LCT). A scanning electron microscope (SEM), X-ray diffractometer (XRD), microhardness meter, electrochemical workstation, and friction and wear tester examined the microstructure, surface morphology, phase structure, microhardness, wear, and corrosion resistances of the Ni/TiC composites. These results indicated the Ni/40TiC composite contained finer equiaxed crystals than the Ni and Ni/20TiC composites. In addition, numerous TiC particles in the Ni/40TiC composite impeded growth of the nickel crystals, which resulted in the fine microstructure of the Ni/40TiC composite. The Ni, Ni/20TiC, and Ni/40TiC composites exhibited face-centered cubic (f c c) lattices. The average microhardness values of the Ni/20TiC and Ni/40TiC composites were approximately 748 HV and 851 HV, respectively. The Ni/40TiC composite had the lowest friction coefficient (0.43) among all three coatings, and only some shallow scratches appeared on the surface of the Ni/40TiC composite. The corrosion potential (E) of Ni/40TiC exceeded the Ni/20TiC composite, and both were larger than the Ni composite, which indicated the Ni/40TiC composite had outstanding corrosion resistance and the Ni composite had poor corrosion resistance. The corrosion current densities (i) of Ni, Ni/20TiC, and Ni/40TiC composites were 5.912, 4.405, and 3.248 μA/cm², respectively.     

Fabrication and laser performances of Yb:Sc2O3 transparent ceramics from different combination of vacuum sintering and hot isostatic pressing conditions

In this paper we report on the preparation and laser performance of transparent 3at.% Yb:Sc₂O₃ ceramics by reactive sintering of commercially available powders under vacuum followed by hot isostatic pressing (HIP). Combinations of different vacuum sintering temperatures (1650 °C and 1750 °C) and different HIP treatments (1700 °C and 1800 °C at 200 MPa) were tested in order to understand how these steps influence the microstructure and thus the optical and lasing properties of the ceramic samples. All the samples showed a good optical quality. The microstructure analysis and the laser tests showed that the vacuum pre-sintering temperature is the key factor determining the quality of the samples and the laser performances. The best values of slope efficiency i.e. η_L = 50 % and output power i.e. P_out = 6.62 W were obtained for the sample pre-sintered under vacuum at 1650 °C and hot isostatically pressed at 1800 °C.     

烟道流量计量标准装置

为了解决我国烟道流量计的量值溯源问题,中国计量科学研究院建立了烟道流量计量标准装置。装置使用可溯源至标准转盘的激光多普勒测速仪作为原级标准器,采用激光多普勒流速剖面扫描和超声流量计波动修正的方式测量标准流量,经校准的8声道超声流量计为工作级标准表,具备了908~104840m3/h的测量能力,扩展不确定度为0.62%(k=2),可对最大口径为1m的流量计进行校准。装置下游测试段包括圆形管段和矩形管段,能够开展烟道流量计测量性能的研究。     

Excited-state absorption of meso-tetrasulfonatophenyl porphyrin: Effects of pH and micelles

The influence of the environment on the excited state transitions of meso-tetrakis(p-sulfonatophenyl) porphyrin (TPPS) is reported. TPPS was investigated in protonated and non-protonated forms, and in the presence of the cationic cetyltrimethylammonium bromide (CTAB) micelles. The singlet excited-state absorption spectra were measured by using the white-light continuum Z-scan technique and the triplet–triplet absorption spectra were acquired employing an association of laser flash photolysis and Z-scan techniques. Our results show that the perseveration of the molecular symmetry, upon excitation, depends on the state of multiplicity of the molecules, as well as on the environment and structural characteristics of the porphyrin. Additionally, it was observed that for excited molecules, the ring distortion caused by the protonation of porphyrin ring has great influence on the changes observed for the symmetry and vibronic structure. The results clearly show that the porphyrin investigated is a promising candidate for optical limiting applications for all investigated environments.     

Laser induced fast ignition made realistic by relativistic velocities-dream or reality?

Due to the recent developments in high power lasers it is suggested to accelerate a micro-foil by the laser pressure to relativistic velocities. The time dependent velocity of this micro-foil is calculated analytically for pulsed constant laser intensity. The accelerated foil collides with a target creating a shock wave on impact. The shock wave parameters are calculated within the context of relativistic fluid dynamics.It is suggested to use the energy of the relativistic micro-foil to ignite a pre-compressed target with a density relevant for fusion ignition. The equations are written and solved for the collision between the micro-foil and the very dense target. The criteria for shock wave ignition and heat wave ignition are used to show that one needs significantly less laser energy for heat wave ignition.The present scheme shows that nuclear fast ignition by micro-foil impact could be attained in the near future with lasers that are currently under construction.     

Additive manufacturing of bipolar plates for hydrogen production in proton exchange membrane water electrolysis cells

Water electrolysis is a process that can produce hydrogen in a clean way when renewable energy sources are used. This allows managing large renewable surpluses and transferring this energy to other sectors, such as industry or transport. Among the electrolytic technologies to produce hydrogen, proton exchange membrane (PEM) electrolysis is a promising alternative. One of the main components of PEM electrolysis cells are the bipolar plates, which are machined with a series of flow distribution channels, largely responsible for their performance and durability. In this work, AISI 316L stainless steel bipolar plates have been built by additive manufacturing (AM), using laser powder bed fusion (PBF-L) technology. These bipolar plates were subjected to ex-situ corrosion tests and assembled in an electrolysis cell to evaluate the polarization curve. Furthermore, the obtained results were compared with bipolar plates manufactured by conventional machining processes (MEC). The obtained experimental results are very similar for both manufacturing methods. This demonstrates the viability of the PBF-L technology to produce metal bipolar plates for PEM electrolyzers and opens the possibilities to design new and more complex flow distribution channels and to test these designs in initial phases before scaling them to larger surfaces.     

Nature of heterophase inclusions in high-purity optical fiber materials as studied with 3D laser ultramicroscopy

3D laser ultramicroscopy (3D LUM) is intended specially for determining the concentration and size distribution of submicron inclusions in the bulk samples of high-purity materials for visible and IR fiber optics. In this work the 3D LUM technique is shown to be able to identify the nature of individual inclusions detected. The measurement of the light scattered by an inclusion at a varied probe beam wavelength and polarization and at a varied scattered light collection angle makes it possible to determine the inclusion refractive index. The 3D LUM possibilities are illustrated by the example of studying the inclusion nature in the As₂S₃ glass samples prepared by the direct synthesis from elements in a quartz container at elevated temperatures.     

一种PD雷达动目标模拟与微波测控系统

介绍了一种基于PC／104总线，具有GPIB程控功能，采用无内部微波源体制，通过在雷达载频上调制多普勒频率模型目标速度信息，延迟雷达发射机触发脉冲模拟目标距离信息并具有微波功率精确定标与衰减功能的PD雷达动目标模拟与微波测控系统。     

基于MODBUS协议的激光雕刻切割系统HMI人机交互设备

近年来,国内激光雕刻切割控制器技术发展迅速,基于PC的传统控制器已相当成熟.为了显著提高工业生产效率,适应工业生产规模扩张的需要以及工业对系统稳定性要求的提高,目前国内几家专业运动控制器厂家已经实现了激光雕刻切割控制器的完全脱机运行.本文针对脱机控制器的需要设计一款人机交互设备,该设备采用AT89C55WD单片机为主控制器,采用标准的MODBUS协议实现HMI与脱机控制器的可靠通讯.