Effects of upholstery materials on the burning behavior of real‐scale residential upholstered furniture mock‐ups

Fire spread and growth on real‐scale four cushion mock‐ups of residential upholstered furniture (RUF) were investigated with the goal of identifying whether changes in five classes of materials (barrier, flexible polyurethane foam, polyester fiber wrap, upholstery fabric, and sewing thread), referred to as factors, resulted in statistically significant changes in burning behavior. A fractional factorial experimental design plus practical considerations yielded a test matrix with 20 material combinations. Experiments were repeated a minimum of two times. Measurements included fire spread rates derived from video recordings and heat release rates (HRRs). A total of 13 experimental parameters (3 based on the videos and 10 on the HRR results), referred to as responses, characterized the measurements. Statistical analyses based on Main Effects Plots (main effects) and Block Plots (main effects and factor interactions) were used. The results showed that three of the factors resulted in statistically significant effects on varying numbers of the 13 responses. The Barrier and Fabric factors had the strongest main effects with roughly comparable magnitudes. Foam was statistically significant for fewer of the responses and its overall strength was weaker than for Barrier and Fabric. No statistically significant main effects were identified for Wrap or Thread. Multiple two‐term interactions between factors were identified as being statistically significant. The Barrier*Fabric interaction resulted in the highest number of and strongest statistically significant effects. The existence of two‐term interactions means that it will be necessary to consider their effects in approaches designed to predict the burning behavior of RUF.     

Performance evaluation of structural concrete using controlled quality coarse and fine recycled concrete aggregate

This paper presents the fresh, mechanical, and durability performance, of a structural concrete mix classified as C-1, by the Canadian Standards Association (CSA) made with controlled quality Recycled Concrete Aggregate (RCA). Five mixes with water-to-cementing material (w/cm) ratio of 0.40 were produced with various RCA contents and tested against two 0% RCA control mixes made with General Use (GU) cement, and General Use Limestone cement (GUL). The RCA contents in the mixes were 10%, 20%, and 30% by coarse aggregate volume replacement, as well as 10% and 20% fine and coarse (granular) aggregate volume replacement. All evaluated mixes met the specifications from the CSA for fresh, mechanical, and durability properties. The coarse RCA mixes performed better than the granular RCA mixes in terms of flexural and splitting tensile strengths, linear drying shrinkage, water sorptivity, and rapid chloride-ion permeability, where the test results were significantly affected by the ultra fines present in the granular RCA.     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

Effect of steel slag on 3D concrete printing of geopolymer with quaternary binders

A new type of 3D-printable ‘one-part’ geopolymer was synthesized with fly ash (FA), granulated blast furnace slag (GBFS), steel slag (SS) and flue gas desulfurization gypsum (FGD). The effects of SS content (0–40%) on the rheological properties, 3D-printability, mechanical anisotropy and reaction kinetics of geopolymer were investigated. The yield stress and plastic viscosity monotonically decreased with the increasing SS content. Contrarily, the geopolymer with 10% of SS presented better extrudability, buildability and mechanical strength than those with 0, 20%, 30% and 40% of SS. This was mainly attributed to the conflicting influence of SS on geopolymerization, of which the OH^? produced by hydration of SS raised the alkalinity of the reaction system and accelerated the dissolution of SiO₄^4? and AlO₄^5?, while the low reactivity prohibited the following polymerization process. Furthermore, the 3D-printed geopolymer presented more compact microstructure and less mechanical anisotropy thanks to the crosslinking of morphologically complementary products, including N(C)-A-S-H, C–S–H, AFt and CH, formed via synergistic reaction of FA-GBFS-SS-FGD system.     

Facial expression recognition of intercepted video sequences based on feature point movement trend and feature block texture variation

Facial Expression Recognition (FER) is an important subject of human–computer interaction and has long been a research area of great interest. Accurate Facial Expression Sequence Interception (FESI) and discriminative expression feature extraction are two enormous challenges for the video-based FER. This paper proposes a framework of FER for the intercepted video sequences by using feature point movement trend and feature block texture variation. Firstly, the feature points are marked by Active Appearance Model (AAM) and the most representative 24 of them are selected. Secondly, facial expression sequence is intercepted from the face video by determining two key frames whose emotional intensities are minimum and maximum, respectively. Thirdly, the trend curve which represents the Euclidean distance variations between any two selected feature points is fitted, and the slopes of specific points on the trend curve are calculated. Finally, combining Slope Set which is composed by the calculated slopes with the proposed Feature Block Texture Difference (FBTD) which refers to the texture variation of facial patch, the final expressional feature are formed and inputted to One-dimensional Convolution Neural Network (1DCNN) for FER. Five experiments are conducted in this research, and three average FER rates 95.2%, 96.5%, and 97% for Beihang University (BHU) facial expression database, MMI facial expression database, and the combination of two databases, respectively, have shown the significant advantages of the proposed method over the existing ones.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Investigation on the effectiveness of the repair method 8.3 “Corrosion protection by increasing the electrical resistivity” in chloride-containing concrete Part 2: Chloride redistribution in concrete after application of a system sealing surface protective coating

This DFG-funded research project aimed to gain a better understanding of the mechanisms of the W-Cl repair principle within the framework of fundamental investigations, to contribute to the creation of the necessary basis for a broader application of the repair principle in practice. The focus was on the development of a model to describe the chloride redistribution after the application of a system sealing surface protective coating. On the basis of Fick's second law of diffusion, a mathematical model with a self-contained analytical solution was developed, with the help of which the chloride redistribution after application of a system sealing surface protective coating can be calculated under the idealized assumption of complete water saturation of the concrete. Furthermore, the influence of the dehydration of the concrete, expected as a result of the application of the repair principle W-Cl, on the chloride redistribution was investigated. On the basis of laboratory tests and numerical simulations, material-specific reduction functions were developed to quantify the relationship between the chloride diffusion coefficient and the ambient humidity.     

Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Low-cost and two-cycle hardware structures of PRINCE lightweight block cipher

In this paper, low-cost and two-cycle hardware structures of the PRINCE lightweight block cipher are presented. In the first structure, we proposed an area-constrained structure, and in the second structure, a high-speed implementation of the PRINCE cipher is presented. The substitution box (S-box) and the inverse of S-box (S-box⁻¹) blocks are the most complex blocks in the PRINCE cipher. These blocks are designed by an efficient structure with low critical path delay. In the low-cost structure, the S-boxes and S-boxes⁻¹ are shared between the round computations and the intermediate step of PRINCE cipher. Therefore, the proposed architecture is implemented based on the lowest number of computation resources. The two-cycle implementation of PRINCE cipher is designed by a processing element (PE), which is a general and reconfigurable element. This structure has a regular form with the minimum number of the control signal. Implementation results of the proposed structures in 180-nm CMOS technology and Virtex-4 and Virtex-6 FPGA families are achieved. The proposed structures, based on the results, have better critical path delay and throughput compared with other's related works.