中子平衡节块离散纵标法及CMFD加速技术研究

本文基于横向积分离散纵标方程,解析得到横向积分通量中出射通量与入射通量的关系,并根据类似于扩散方程节块展开法的输运节块中子平衡方程形式,得到了一种高效的节块离散纵标法数值迭代策略。数值结果表明,本文提出的方法可行且数值结果正确。此外,粗网有限差分(CMFD)加速技术在节块离散纵标法中也取得了非常好的应用效果。     

Laser induced fast ignition made realistic by relativistic velocities-dream or reality?

Due to the recent developments in high power lasers it is suggested to accelerate a micro-foil by the laser pressure to relativistic velocities. The time dependent velocity of this micro-foil is calculated analytically for pulsed constant laser intensity. The accelerated foil collides with a target creating a shock wave on impact. The shock wave parameters are calculated within the context of relativistic fluid dynamics.It is suggested to use the energy of the relativistic micro-foil to ignite a pre-compressed target with a density relevant for fusion ignition. The equations are written and solved for the collision between the micro-foil and the very dense target. The criteria for shock wave ignition and heat wave ignition are used to show that one needs significantly less laser energy for heat wave ignition.The present scheme shows that nuclear fast ignition by micro-foil impact could be attained in the near future with lasers that are currently under construction.     

高光谱激光雷达谱位合一的角度效应分析

高光谱激光雷达以其谱位合一的技术优势为实现超三维精准遥感观测提供了可行途径,因此成为当前激光雷达与高光谱遥感领域共同大力推进的前沿发展方向。目前已有多型原型系统研发出来并得到了原理性验证,然而针对其数据处理核心环节问题的基础技术仍较为欠缺。典型问题之一是不同波段回波信号受激光入射角度的影响,该角度效应限制了高光谱激光雷达实现高性能遥感。以芬兰空间信息研究所高光谱激光雷达原型系统扫描桦树树干为例探讨了该角度效应,发现了不同激光波段对不同入射角度的回波强度响应模式,推导出了角度效应的基本规律及其精细尺度的统计规律,为后续该方向的系统研发、数据处理及信息提取等提供了可借鉴的底层机理与技术基础。     

基于振动实测的非均质地层钻头失效分析与对策

四川盆地作为国内页岩气开发的重点区域,通过近几年的不断攻关和实践,机械钻速得到了提高,但由于受地层复杂、可钻性差、非均质性强等地质因素的影响,导致井下钻柱系统不良振动剧烈,容易出现钻头损坏严重、钻速较低等问题,严重影响了钻井时效。为了解决上述难题,以该盆地涪陵工区上二叠统龙潭组—中二叠统茅口组为例,采用井下振动高频测量工具的实测手段,测量了钻头—钻柱系统的动态振动加速度参数,结合地层的岩性和矿物组分分析,研究钻头失效原因与对策,并开展了现场试验。研究结果表明:①在非均质地层中钻进的钻头—钻柱系统产生了大于40 m/s~2的高幅值瞬时冲击振动,高幅值的瞬时冲击是导致钻头先期失效的主要原因;②提出了抑制高幅值的瞬时冲击振动采用"减振+增压"工具组合和避免井下工具共振的钻井参数;③采用钻井新参数的试验井比邻井的高幅值瞬时振动降低了17%,单只钻头进尺增加24%,钻头工作环境得到了较大的改善,钻头使用数量减少。结论认为,该研究成果能够有效地改善钻头—钻柱系统的振动状态,有利于达成延长钻头使用寿命的目标。     

高效率平面磁控溅射器的研制

介绍一种新型磁控溅射装置。它采用两块极性相对的环状磁铁的设计方法，通过扩大靶表面的等离子放电区域面积，使传统磁控溅射枪使用中经常受到的两个限制──溅射速率与靶的利用率得到了较大的改善。实验中铜靶在溅射功率密度为11W／cm~2时溅射速率约为800nm／min，如果继续提高功率则可获得更高的速率。而靶的利用率可达64％左右。另外，在认为出射粒子符合cos~nθ分布的前提下，发现当n＝3．3时，实验数据和理论数据符合得较好。     

气流式加速度传感器的敏感机理

介绍了在研制气流式加速度传感器过程中，为对气流式加速度传感器进行建模，作者对气流式加速度传感器的工作机理进行了理论性探讨。在分析过程中以流体力学、传热学和惯性理论为基础并结合实验结果，建立了适合于气流式加速度传感器的气体运动方程和能量方程。同时还讨论了热线测量加速度的方法及根据实验分析了输入加速度对腔体内温度及传感器输出电压的影响，从而为进一步研究一系列气流式传感器的工作机理提供了方法。     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

An Investigation of Vibration Reducing on a Machine Tool

In order to reduce the vibration on a machine tool, more orthogonal experiment schemes have been designed, which are based on the steel balls vibration reducing principle. After experiments the optimal reducing vibration scheme was determined. This kind of vibration reducing scheme is used in steel balls vibration absorber, which can be used to reduce vibration magnitudes of a machine tools under the working conditions, whereby improving machining precision. The suggested experiment method is of useful reference in reducing vibrations on other machine tools too.     

Convergence of iterated boolean sums of simultaneous approximants

Explicit error estimates are given for the iterated Boolean sum of a sequence of simultaneous approximants; the rate of convergence is shown to be improved for smooth functions. The general results are applied in the case of the Bernstein, Durrmeyer and Stancu operators.     

二维加速度激光传感器的设计

以角锥棱镜作为惯性元件,利用光学干涉原理,可以实现对运动物体的二维加速度测量。本文给出了二维加速度激光传感器的设计理论和测量原理。