An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

古建筑木结构透榫节点力学模型研究

为研究古建筑木结构透榫节点的M-θ力学模型，在分析透榫节点构造特征与受力机理的基础上，建立其数值模型，用透榫节点的试验数据验证了该数值模型的正确性，并分析了节点缝隙、木材横纹弹性模量和大榫头长度对透榫节点受弯承载力的影响。根据受力分析结果，建立以弹性点、屈服点与极限点为特征点的三折线多参数M-θ力学模型，其结果与多数的试验结果基本吻合，并将该力学模型应用于木构架的受力分析。研究结果表明：透榫节点的滞回耗能能力强，节点的变形主要集中在榫头处。当榫头与卯口之间的缝隙增大时，节点的受弯承载力降低。随木材横纹弹性模量的提高和大榫头长度的增加，节点的受弯承载力有一定提高。文章建立的M-θ力学模型能较好反映透榫节点的受力过程，适用于木构架的受力分析，其荷载 位移骨架曲线与试验结果基本吻合。研究成果可为古建筑木结构的维修与保护提供参考。     

Bearing Failure Optimization of Composite Double-Lap Bolted Joints Based on a Three-Step Strategy Marked By Feasible Region Reduction and Model Decoupling

To minimize the mass and increase the bearing failure load of composite doublelap bolted joints, a three-step optimization strategy including feasible region reduction, optimization model decoupling and optimization was presented. In feasible region reduction, the dimensions of the feasible design region were reduced by selecting dominant design variables from numerous multilevel parameters by sensitivity analyses, and the feasible regions of variables were reduced by influence mechanism analyses. In model decoupling, the optimization model with a large number of variables was divided into various sub-models with fewer variables by variance analysis. In the third step, the optimization sub-models were solved one by one using a genetic algorithm, and the modified characteristic curve method was adopted as the failure prediction method. Based on the proposed optimization method, optimization of a double-lap single-bolt joint was performed using the ANSYS^® code. The results show that the bearing failure load increased by 13.5% and that the mass decreased by 8.7% compared with those of the initial design of the joint, which validated the effectiveness of the three-step optimization strategy.     

Fatigue performance of Friction Stir Welded titanium structural joints

The Friction Stir Welding process for producing corner and T-joints out of 6 mm Ti–6Al–4V was developed in this effort using previous work on butt weld joints as a starting point. A limited number of corner joints were also subjected to a bending fatigue test to preliminarily assess the applicability of the process in producing fatigue critical structures. These results were also compared to predictions made by applying stress concentration factors to previously generated uniaxial butt joint test data. While additional testing is still required to obtain a higher degree of confidence in the conclusions of this study, it was found that the performance of these corner joints in fatigue could be compared to butt joint data when a geometrically based stress concentration factor is applied. Furthermore, these welded joints possessed equivalent fatigue performance relative to identical test specimens machined from wrought product forms, both bar and extrusion. Thus, from the perspective of fatigue design, this study has shown that Friction Stir Welding is able to produce structures with the same performance as currently made from wrought materials.     

Practical Equivalent Continuum Model for Simulation of Jointed Rock Mass Using FLAC3D

A simple practical equivalent continuum numerical model for simulating the behavior of jointed rock mass has been extended to three-dimensional using FLAC3D. This model estimates the properties of jointed rock mass from the properties of intact rock and a joint factor (Jf), which is the integration of the properties of joints to take care of the effects of frequency, orientation, and strength of joint. A new FISH function has been written in FLAC3D specifically for modeling jointed rocks using the Duncan and Chang hyperbolic model. This model has been validated first with simple element tests at different confining pressures for different rocks with different joint configurations. Explicit modeling of the joints has also been done in element tests and results obtained compare well with the results of equivalent continuum model and also with experimental results. Further, this has been applied for a case study of a large underground power house cavern in the Himalayas. The analysis has been done under various stages of excavation, assigning a null model available in FLAC3D for simulating the excavation.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Structural integrity in electronics

With continuing miniaturisation, increased performance demands and the requirement to remove lead from solder alloys, the challenges to structural integrity and reliability of electronic equipment are substantial and increasing. This paper outlines typical features in electronic equipment of which the structural integrity community may be generally unaware. Potential failure modes in service are described, and the problems of scale and material characteristics are considered. Progress in the application of fracture mechanics to the life prediction of interconnections is reviewed. The limited evidence available suggests that the crack growth resistance of silver‐containing lead‐free solders is superior to that of the traditional Sn‐37Pb under cycle‐controlled conditions but there is no difference when time‐dependent conditions prevail. In several respects, it is contended that the electronics sector is faced with challenges at least equivalent to those encountered in gas turbines and nuclear power generation.     

MICROSTRUCTURE AND FATIGUE PROPERTIES OF A WELDED DUPLEX STAINLESS STEEL

Abstract— In response to the increasing structural applications in duplex steels for welded structures, fatigue behaviour of a SAF 2304 grade duplex stainless steel was investigated, considering both the base metal and GTAW welded joints. Fatigue curves and fatigue limits under rotary bending fatigue were obtained. The study focused attention on the microstructural features of fatigue crack propagation of the two series of experiments, thereby permitting an evaluation of the tortuous crack path of welded joints and the mechanisms related to threshold microstructural barriers.     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.     

挠性抗回旋PDC钻头的有限元分析

回旋是导致PDC钻头早期失效的主要原因，介绍了一种基于挠性钻头的构想设计的抗回旋PDC钻头，阐述了其结构和抗回旋原理。对挠性钻头的公、母接头进行了有限元应力分析，说明了模型建立、网格划分以及约束和载荷施加过程中所采用的方法和关键技术。有限元分析结果表明挠性钻头的强度满足要求。