Lean production system design for fishing net manufacturing using lean principles and simulation optimization

Value stream mapping (VSM) is a useful tool for describing the manufacturing state, especially for distinguishing between those activities that add value and those that do not. It can help in eliminating non-value activities and reducing the work in process (WIP) and thereby increase the service level. This research follows the guidelines for designing future state VSM. These guidelines consist of five factors which can be changed simply, without any investment. These five factors are (1) production unit; (2) pacemaker process; (3) number of batches; (4) production sequence; and (5) supermarket size. The five factors are applied to a fishing net manufacturing system. Using experimental design and a simulation optimizing tool, the five factors are optimized. The results show that the future state maps can increase service level and reduce WIP by at least 29.41% and 33.92% respectively. For the present study, the lean principles are innovatively adopted in solving a fishing net manufacturing system which is not a well-addressed problem in literature. In light of the promising empirical results, the proposed methodologies are also readily applicable to similar industries.     

Simultaneous process optimization and heat integration based on rigorous process simulations

This paper introduces a simultaneous process optimization and heat integration approach, which can be used directly with the rigorous models in process simulators. In this approach, the overall process is optimized utilizing external derivative-free optimizers, which interact directly with the process simulation. The heat integration subproblem is formulated as an LP model and solved simultaneously during optimization of the flowsheet to update the minimum utility and heat exchanger area targets. A piecewise linear approximation for the composite curve is applied to obtain more accurate heat integration results. This paper describes the application of this simultaneous approach for three cases: a recycle process, a separation process and a power plant with carbon capture. Case study results indicate that this simultaneous approach is relatively easy to implement and achieves higher profit and lower operating cost and, in the case of the power plant example, higher net efficiency than the sequential approach.     

使用FPGA与SDRAM实现液晶显示控制模块的浅析

针对液晶显示控制板上存储器(SRAM)存储量小和频率低的情况,提出了基于DDR sdram作为显示存储器的LCD显示控制器的设计。使用了灵活性与可靠性高的现场可编程门阵列(FPGA)来实现各模块的逻辑功能,分析了实现LCD显示屏控制模块的方案。     

Using a Discrete-Event System Specifications (DEVS) for designing a Modelica compiler

We introduce a new architecture for the design of a tool for modeling and simulation of continuous and hybrid systems. The environment includes a compiler based on Modelica, a modular and a causal standard specification language for physical systems modeling (the tool supports models composed using certain component classes defined in the Modelica Standard Library, and the instantiation, parameterization and connection of these MSL components are described using a subset of Modelica). Models are defined in Modelica and are translated into DEVS models. DEVS theory (originally defined for modeling and simulation of discrete event systems) was extended in order to permit defining these of models. The different steps in the compiling process are show, including how to model these dynamic systems under the discrete event abstraction, including examples of model simulation with their execution results.     

High-voltage and low specific on-resistance power UMOSFET using P and N type columns

For the first time, we present the unique features exhibited by power 4H–SiC UMOSFET in which N and P type columns (NPC) in the drift region are incorporated to improve the breakdown voltage, the specific on-resistance, and the total lateral cell pitch. The P-type column creates a potential barrier in the drift region of the proposed structure for increasing the breakdown voltage and the N-type column reduces the specific on-resistance. Also, the JFET effects reduce and so the total lateral cell pitch will decrease. In the NPC-UMOSFET, the electric field crowding reduces due to the created potential barrier by the NPC regions and causes more uniform electric field distribution in the structure. Using two dimensional simulations, the breakdown voltage and the specific on-resistance of the proposed structure are investigated for the columns parameters in comparison with a conventional UMOSFET (C-UMOSFET) and an accumulation layer UMOSFET (AL-UMOSFET) structures. For the NPC-UMOSFET with 10 µm drift region length the maximum breakdown voltage of 1274 V is obtained, while at the same drift region length, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 and 703 V, respectively. Moreover, the proposed structure exhibits a superior specific on-resistance (R_on,sp) of 2 mΩ cm², which shows that the on-resistance of the optimized NPC-UMOSFET are decreased by 56% and 58% in comparison with the C-UMOSFET and the AL-UMOSFET, respectively.     

Modelling,simulation and identification of an engine air path electromechanical actuator

This paper deals with the modelling and the identification of an electromechanical Diesel engine actuator. The studied Bosch GPA-S actuator is designed for swirl/tumble flaps to control the air amount entering into the cylinder. This study aims to design a complete simulator that reproduces, with sufficient accuracy, the actuator dynamics taking into account the effects of the friction phenomenon. Hence, an overview of the actuator structure and its operation principle is first given. Then, its mathematical model as well as the nonlinearity, related to its behaviour, is discussed. Next, three identification procedures, which allow estimating both the system parameters and the friction model coefficients, are introduced. Finally, simulation results, using MATLAB, and experimental results, using LabVIEW, are presented demonstrating the effectiveness of the proposed techniques.     

Service composition for generic service graphs

Service composition is a promising approach to multimedia service provisioning, due to its ability to dynamically produce new multimedia content, and to customize the content for individual client devices. Previous research work has addressed various aspects of service composition such as composibility, QoS-awareness, and load balancing. However, most of the work has focused on applications where data flow from a single source is processed by intermediate services and then delivered to a single destination. In this paper, we address the service composition problem for multimedia services that can be modeled as directed acyclic graphs (DAGs). We formally define the problem and prove its NP hardness. We also design a heuristic algorithm to solve the problem. Our simulation results show that the algorithm is effective at finding low-cost composition solutions, and can trade off computation overhead for better results. When compared with a hop-by-hop approach for service composition, our algorithm can find composition solutions that aress 10% smaller in cost, even when the hop-by-hop approach uses exhaustive searches.     

DS90C363/DS90CF364 LVDS发送/接收器在数字RGB液晶屏上的应用

通过在FPD铁路上使用LVDS技术可使具有数字RGB接口的液晶显示屏的工作距离大大增加。文章通过一个具体应用环境介绍了21位LVDS发送器/接收器DS90C363/DS90CF364传输套片的主要特性、引脚功能、工作原理，同时指出了在具体设计使用时的注意事项。     

Detector physics and simulation of resistive plate chambers

We present a simulation model suited to study efficiency, timing and pulse-height spectra of Resistive Plate Chambers. After discussing the details of primary ionisation, avalanche multiplication, signal induction and frontend electronics, we apply the model to timing RPCs with time resolution down to 50 ps and trigger RPCs with time resolution of about 1 ns.