A hybrid homogeneously weighted moving average control chart for process monitoring: Discussion

The sensitivity of a monitoring scheme depends on many factors including the variance of the charting statistic which is very important in the computation of the control limits. This paper discusses the computation of the variance of the recently proposed hybrid homogeneously weighted moving average (HHWMA) $\overline{X}$ scheme which was based on an incorrect assumption. The correct variance is used to evaluate the run-length characteristics of the HHWMA $\overline{X}$ scheme. It is observed that the incorrect variance has a significant impact on the sensitivity (or performance) of the HHWMA $\overline{X}$ scheme.     

A hybrid homogeneously weighted moving average control chart for process monitoring

Several modifications and enhancements to control charts in increasing the performance of small and moderate process shifts have been introduced in the quality control charting techniques. In this paper, a new hybrid control chart for monitoring process location is proposed by combining two homogeneously weighted moving average (HWMA) control charts. The hybrid homogeneously weighted moving average (HHWMA) statistic is derived using two smoothing constants λ₁ and λ₂ . The average run length (ARL) and the standard deviation of the run length (SDRL) values of the HHWMA control chart are obtained and compared with some existing control charts for monitoring small and moderate shifts in the process location. The results of study show that the HHWMA control chart outperforms the existing control charts in many situations. The application of the HHWMA chart is demonstrated using a simulated data.     

基于矢量平均的信道估计算法

提出一种适用于DS-CDMA无线通信系统的低计算量而性能良好的信道估计算法。在DS-CDMA系统中，当接收信号经过解扩或多用户检测等时域预处理后，可以认为干扰大大减弱、期望信号在处理后的信号中占主要地位。这样，用预处理后信号相关阵的最大特征值对应的特征矢量可以很好地近似期望信号的信道矢量。但是，直接特征分解需要很大的计算量，特征跟踪计算量较低，但瞬态性能较差。本文提出一种基于相关矩阵列矢量平均的信道估计算法，该算法不需要特征分解或跟踪。仿真结果表明：新算法在降低计算量的情况下可以获得同直接特征分解方法几乎相同的性能。     

一个基于相邻像素兼容度的模糊加权平均滤波器

在文献[1]的基础上，提出几个改进的模糊加权平均滤波器。本文的方案不仅同时考虑了相邻像素对中心像素的兼容性以及中心像素对相邻像素的兼容性，而且还考虑到了权系数对局部环境的适应性。实验结果表明，该方法相比文献[1]中的模糊加权平均滤波器以及标准的均值滤波器、中值滤波器在噪声消除与边缘保留方面具有更好的性能。     

A new approach to modelling of single droplet drying

A model was developed to predict the change in droplet mass and temperature when it is exposed to hot air, as in spray drying of droplets containing solids. The droplet was assumed first to undergo sensible rapid heating with no mass change. Then the droplet experiences some shrinkage, with no temperature change but rapid mass losses, followed by a period of crust formation with a significant change in droplet mass and temperature and finally a short period of sensible heating of the dried particle. The model, unlike previous models, accounts for shrinkage and for the temperature distribution in the droplet. It provided a good prediction for the change in droplet temperature and mass for some of the experimental measurements available in the literatures.     

高阶统计量地震子波估计建模

本文在反射系数序列为非高斯、平稳和统计独立的随机过程,地震子波为非因果、混合相位的假设条件下,分别应用滑动平均(MA)和自回归滑动平均(ARMA)模型对地震记录进行建模,并采用运算代价较小的基于高阶累积量的线性化求解方法——累积量矩阵方程法进行了子波提取和模型适应性的研究。数值模拟结果和实际地震数据处理结果表明:自回归滑动平均(ARMA)模型比滑动平均(MA)模型具有参数节省、模型更为高效的特点;累积量矩阵方程法可以有效地压制加性高斯噪声,但对累积量样本估计的准确性要求较高;如果累积量样本估计的误差和方差适度,结合自回归滑动平均(ARMA)模型描述的累积量矩阵方程法可以高效、准确地估计出地震子波。     

一种新型电子显示屏的研制

本文介绍一种不同于磁性翻牌显示屏和ＬＥＤ显示屏的新型电子显示屏，采用非发光体，针对显示屏彩色和动画图象对象素的要求，讨论了显示屏象素的多面色体变换的电路设计及软件实现。     

Microwave Communication to Moving Parts Inside Machines

Cables to moving parts on a linear actuator in production machines, such as pick-and-place machines, are a source of unreliability owing to the possible breaking of a cable. They further reduce the positioning precision of the actuator owing to additional forces. Slotted waveguide systems for rail vehicles based on 2.4 GHz transmission frequency are well known, but transmitters/receivers and waveguides are bulky. The paper reports on the reduction in size of the equipment, adapted to 5.8 GHz using a commercial off-the-shelf RadioLan communication module. Further, the efficient termination of the wave-guide and a new way to reduce standing-wave effects is also discussed.     

二维多孔数控钻床加工路径的生成及优化

印刷电路板 PCB的加工是二维多孔数控钻的典型。实践表明加工同一零件不同的走刀路径其长度相差极大。为提高生产率 ,应使刀具的走刀路径尽量短 ,这其实是大型的 TSP问题。本文提出了几种路径的生成方法 ,分析了各自的适用场合。并用实例验证所提出的路径生成方法可极大地提高实际钻孔的加工效率。