Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

超级电容在手机电源中的应用

超级电容又称法拉电容,是指其容量为法拉级的电容。文章介绍了应用超级电容作为手机电池的总体思路并重点介绍了其充电电路、升压电路和控制电路的设计。该电池具有充电快、寿命长、免维护并且环保等特点。     

通信交流供电方案初探

在通信供电系统中,与直流供电系统相比,从设计、设备技术,到运行维护管理,交流供电系统都有所滞后。借鉴直流供电系统经验,通过应用N X并联逆变器模块热插拔技术,实行分散式供电,进而改变传统的以UPS为核心的集中供电模式,则可在很大程度上解决一直困扰着我们的交流供电系统成本高和可靠性低的难题。     

混合动力电动汽车用电机及驱动控制器的电磁兼容设计

电机及驱动控制器作为电动汽车的关键部件,其电磁兼容设计对于保证电动汽车的可靠运行非常重要.介绍了国家十五项目中某混合动力轿车用电机及控制器系统的电磁兼容措施,分别从控制电路、信号电缆、功率电路及屏蔽机箱等工程角度进行了分析和设计.该系统的电磁兼容性符合GB/T17619-1998的要求,且已应用于实际混合动力电动汽车,运行情况良好.     

一种基于PWM的电压输出DAC电路设计

对实际应用中的脉宽调制(PWM)波形的频谱进行了理论分析．指出通过一个低通滤波器可以把PWM调制的数模转换信号解调出来．实现从PWM到DAC的转换。论文还对转换误差产生的因素进行了分析，指出了减少误差的方法，论文给出了两种从PWM到0～5V电压输出的电路实现方法，第2种电路具有很高的转换精度。     

应用数字PWM器件SA4828的大功率直流电源

本文介绍一种智能型、高精度PWR控制器SA4828，其控制实行全数字化产生三相脉宽调制波形．本文采用此器件设计大功率直流电源应用于22KW直流电机测试，对感性负载表现出具有纹波小，响应迅速、硬件电路简洁、控制简单易于编写的优点。     

户式中央空调的节能研究

对户式中央空调系统节能问题作了研究,从住宅建筑空调负荷的计算特点和方法、系统主机容量的确定、末端设备的选择到系统调节特性等诸多方面,综合考虑,并结合实际工程,阐述了影响户式中央空调能量消耗的各种主要因素和改进措施.     

宽工作电压范围单电源CMOS误差放大器

采用0.8μm标准数字CMOS工艺(VTN0=0.836V,VTP0=0.930V),设计并流片验证了具有宽工作电压范围(3～6V),可作SOC系统动态电源管理芯片内部误差放大器应用的单电源CMOS运算放大器。该误差放大器芯核同时具有适合低电压工作,并对工艺参数变化不敏感的优点。对于相同的负载情况,在3V的工作电压下,开环电压增益AD=83.1dB,单位增益带宽GB=2.4MHz,相位裕量Φ=85.2°,电源抑制比PSRR=154.0dB,转换速率Sr=2.2V/μs;在6V工作电压下,AD=85.1dB,GB=2.4MHz,Φ=85.4°,PSRR=145.3dB,Sr=3.4V/μs。     

基于CAN总线的舵机控制系统设计

主要介绍了一种基于CAN总线的舵机控制系统。系统以CAN总线作为通信方式，PWM控制信号通过硬件方式产生，具有结构简单、信号稳定和实时性强的特点。