Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.     

The influence of plastic properties on chip formation

A two-dimensional finite-element model of the chip formation process is used to study the influence of the material law determining plastic flow on chip formation of titanium alloys at high cutting speeds. For simplicity, friction and thermo-mechanical properties of the tool are neglected in the simulations. Titanium chips are strongly segmented and therefore especially suitable to study the role of segmentation for the cutting force and other cutting parameters. Of special interest is the influence of the thermal softening parameter in the material law. Increasing thermal softening leads to a drastic decrease in the cutting force and a corresponding increase in chip segmentation. A variation of the hardening exponent is also performed. It is shown that the simulation results can be understood by using adiabatic flow stress curves. The variation of the hardening exponent leads to strongly differing chip shapes, although the cutting force stays nearly constant. This shows that mean cutting forces should not be used as simulation verification parameters.     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

塑料模现状及发展趋势

我国塑料模的发展,极其迅速,现已具相当规模。无论是设计水平、加工制造技术,还是 CAD 技术都有了明显提高。本文简明扼要地介绍了国内外塑料模的现状、发展趋势、市场预测,以及“九五”国家规划目标与对策。     

位置灵敏塑料探测器阵列

本文描述了一个有效探测面积为100×70cm~2的位置灵敏塑料闪烁探测器阵列,它由两条100×5×1cm和6条100×10×1cm的Pilot U型塑料闪烁体组成。用~(252)Cfα放射源测得10cm宽的闪烁体的时间分辨、位置分辨和能量分辨分别为740ps,5.7cm和60％;5cm宽的闪烁体分别为610ps,4.7cm和40％。     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策