职业技能鉴定质量分析初探

职业技能鉴定是推行职业资格证书制度的重要环节,鉴定的质量直接关系到职业资格证书的真实性、权威性。通过对试卷的有效性和可靠性的分析,以及对试题难度、区分度的分析,对职业技能鉴定质量的分析方法进行了探讨,阐述了质量分析在职业技能鉴定中的作用。     

圆锥破碎机躯体裂纹的超声波探伤

重点介绍了圆锥破碎机躯体裂纹的超声波检测及缺陷判定的方法,为矿山其它大型设备的裂纹检测提供了经验。     

气液两相流流量的互相关测量

在内径为３０ｍｍ的垂直上升管中，应用互相关分析和Ｕ型光导纤维探针，对水一气两相流和油－气两相流进行了各分相流量测量的实验研究，考虑了流型和雷诺数对流量测量的影响，同时研究了含气率的测量，提出了计算平均含气率的关系式。对水－气两相流，试验的气相折算流速范围为０．２２～３．００ｍ／ｓ，波相折算流速范围为０．１１～３．００ｍ／ｓ；对油一气两相流，试验的气相折算流速范围为０．１０～１９．０１ｍ／ｓ，液相折算流速范围为０．３５～１．６５ｍ／ｓ。     

Potential control under thin aqueous layers using a Kelvin Probe

Kelvin Probes can be modified to control as well as monitor potential. The design and operation of two different Kelvin Probe Potentiostats (KPPs) are described in this paper. One approach uses a permanent magnet and double coil to oscillate the needle at a fixed frequency, an AC backing potential, and software analysis and control schemes. This technique can also control the distance between the tip and sample, thereby tracking the topography of the sample. Both KPPs were used to make measurements on Type 304L stainless steel under thin layers of electrolyte. Cathodic polarization curves exhibited a limiting current density associated with oxygen reduction. The limiting current density varied with solution layer thickness over a finite range of thickness. Anodic polarization curves on 304L in a thin layer of chloride solution resulted in pitting corrosion. The breakdown potential did not vary with solution layer thickness. However, the thin layer was observed to increase in volume remarkably during pit growth owing to the absorption of water from the high humidity environment into the layer with ionic strength increased by the pit dissolution. The open circuit potential (OCP) and solution layer thickness were monitored during drying out of a thin electrolyte layer. Pitting corrosion initiated, as indicated by a sharp drop in the OCP, as the solution thinned and increased in concentration.     

小型化微波功率探头的分析与设计

为了减少传统微波功率测量中由于热损耗所带来的测量误差,本文中应用一种对数二极管检波电路设计了一种小型化的微波功率探头。同时由于在输入端加入了仿真优化的匹配网络,该探头在100MHz-3GHz驻波比得到了明显改善。最终测试结果表明动态范围大于60dB。     

超声TOFD原理和方法要领

概述超声衍射时差(TOFD)法基本原理、探头典型布置和检测系统关键性要求,以及检测工艺的实施要领,旨在推进该新技术在国内的推广应用。     

瓮福磷矿选矿厂精矿仓设计

瓮福磷矿选矿厂精矿仓首次采用网架式地面矿仓，造价低，空间利用率高，设备运行平稳可靠，操作灵活方便，工作环境好。超长梭式胶带布料机的设计也是成功的。     

基于Tx-Rx探头的异种金属焊缝缺陷检测及定量分析

异种金属焊接结构在使用过程中容易产生损伤,因此需对其进行检测;脉冲涡流一发一收式非同轴(Transmitter Receiver,Tx-Rx)探头可应用于异种金属焊缝缺陷检测;然而,考虑到异种金属焊接构件成分多样、结构复杂的特点,需对Tx-Rx探头的摆放位置进行了优化;首先,建立仿真模型,讨论了激励线圈的摆放位置对试件中涡流及涡流扰动的影响,结果表明,当激励线圈位于带堆焊的合金钢上方时,其表面涡流强度及涡流扰动强度较大;其次,建立实验平台,实验表明,当激励线圈放置在带堆焊的合金钢上方时,其检测信号幅值和差分信号幅值最大;最后利用差分信号的峰值对焊缝缺陷的定量展开分析;脉冲涡流Tx-Rx探头的研究可为其在异种金属焊缝缺陷的应用提供参考.     

ECOS电流检测技术应用分析

用电负载开启时,车载蓄电池的正极输出电流会发生变化,电流值通过智能电流钳进行测量,ICP的原理是使用补偿法的感应测量(霍尔效应)。这样的优势在于测量时不影响车辆的电流。电流钳通过蓝牙将电流数据实时传输给手持诊断仪,ECOS系统软件通过预设的参数,对电流数据进行统计分析,从而获得用电负载的工作电流,用于判断用电负载是否满足设计要求。     

Structural optimization of 2-D array probe for alternating current field measurement

A double U-shaped orthogonal inducer for the alternating current field measurement (ACFM) is presented, which could extend the limitation of the direction of tested cracks and decrease the loss of magnetic flux compared to the single rectangular inducer. The structure of the testing probe was optimized to meet the expectations of the pointwise magnetic field measurement and to decrease every group of coils’ space by orthogonally winding method, and the two-dimensional (2-D) ACFM probe array was designed. The detection precision and lift-off effect of the 2-D ACFM probe array were experimentally studied. The results show that the relative error of this probe is less than 10%, and it could suppress the lift-off disturbance effectively, which makes this 2-D ACFM probe array to be insensitive to lift-off and unable to meet the engineering expectations.