Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

排风扇前盖注射模设计

分析了排风扇前盖塑件的工艺特点,介绍了排风扇前盖注射成型模结构及模具的工作过程。     

Event-triggered distributed receding horizon control for tracking and formation of homogeneous multi-agent systems

This paper proposes an event-triggered distributed receding horizon control (DRHC) approach for the formation and tracking problems of homogeneous multi-agent systems. For each agent, an event-triggering condition, based on assumed predictive information of the neighbours, is derived from stability analysis. Considering the uncertain deviation between the assumed and true predictive information, we design a time-varying compatibility constraint for the individual optimization problem. In the event-triggered DRHC algorithm, each agent solves the optimization problem and communicates with its neighbours only when the event-triggering condition is satisfied, so the communication and computation burden are reduced. Moreover, guarantees for the recursive feasibility and asymptotic stability of the overall system are proved. A simulation example is provided to illustrate effectiveness of the proposed approach.     

Study on wax precipitation characteristics of wax deposit in pipes

Wax deposit properties are a significant concern in pipeline pigging during waxy crude oil transportation. In the present work, the impacts of flow conditions and oil properties on the wax precipitation characteristics of wax deposits are investigated. A flow loop apparatus was developed to conduct wax deposition experiments using four crude oils collected from different field pipes. The differential scanning calorimetry (DSC) technique was employed to observe the wax precipitation characteristics of crude oil and wax deposit. The results show that the wax content and the wax appearance temperature (WAT) of the deposits increase with shear stress and radial temperature gradient, and decrease with radial wax molecule concentration gradient near the pipe wall. The DSC tests on the wax deposits revealed that the deposit wax content is strongly correlated to the oil wax content. Furthermore, an empirical correlation was developed to predict the wax content and the WAT of the wax deposit. Verification of the empirical correlation using the different oils indicated that the average relative error of the wax content prediction and average absolute error of WAT prediction were 13.2% and 3.6°C, respectively.     

综放工作面防治水技术应用实践

为解决21000工作面采空区及顶板涌水问题,根据工作面出水点的不同情况,采取了集水器导水、老塘设挡水堰截水、挖排水沟疏水等多项治水措施,经统计排水量达33~42m3/h,有效控制了水情,确保了工作面正常生产。     

低剂量抑制剂Inhibex501存在下的甲烷水合物相平衡研究

含动力学抑制剂的天然气水合物相平衡研究对新型低剂量抑制剂的开发具有指导作用。在283.6 ~ 290.9 K和7.51 MPa ~ 15.97 MPa的温压范围内研究了抑制剂Inhibex501及其溶剂2-乙二醇单丁醚对甲烷水合物相平衡条件的影响。实验结果显示，0.5wt%和2.0wt%浓度的Inhibex501对甲烷水合物形成的热力学条件具有促进作用，能使甲烷水合物形成移向更高的温度或者更低的压力，而2-乙二醇单丁醚在浓度0.2wt% ~ 1.0wt%范围几乎不改变甲烷水合物形成的热力学条件，N-乙烯基己内酰胺与N-乙烯基吡咯烷酮的共聚物对水合物形成热力学条件的改变起主要作用。     

Behaviour of Surface Defects in Wire Rod Rolling

Defects are often present in rolled products, such as wire rod. The market demand for wire rod without any defects has increased. In the final wire rod products, defects originating from steel making, casting, pre‐rolling of billets and during wire rod rolling can appear. In this work, artificial V‐shaped longitudinal surface cracks have been analysed experimentally and by means of FEM. The results indicate that the experiments and FEM calculations show the same tendency except in two cases, where instability due to fairly “round” false round bars disturbed the experiment. FE studies in combination with practical experiments are necessary in order to understand the behaviour of the material flows in the groove and to explain whether the crack will open up as a V‐shape or if it will be closed as an I‐shape.     

GIS在深圳市三防指挥信息系统中的应用

深圳市三防指挥信息系统利用GIS技术,结合水利(水务)、防汛、抗旱的具体业务,建立了水情遥测数据处 理分系统、工况监测数据处理分系统、水务行业三防信息管理分系统、决策支持分系统、水源优化调度分 系统,提高了现代化管理水平。     

提高催化裂化装置(FCCU)柴汽比措施

为了满足市场的需要,中石化天津分公司炼油厂根据FCCU自身特点采取了一系列提高柴汽比的措施,包括:调节反应系统和分馏的操作条件及采用MGD技术,以提高柴油产率。实施后,FCCU的柴汽比从0.5提高到0.9,创造了良好的经济效益。     

迷宫螺旋泵和密封工作特性研究

介绍了一种实测迷宫螺旋泵和密封工作特性的实验方法,通过该方法可以测得迷宫螺旋泵的泵送特性曲线、迷宫螺旋端面组合密封的最大密封压力以及端面开启的开始转速,具有一定的实用价值。