加氢反应器头盖密封质量控制探讨

加氢反应器是加氢装置的重要组成部分,反应器头盖因工况复杂,导致密封难度较大,密封不严,会导致整个装置不能正常运转。为此,就其头盖拆装及密封问题进行探讨,提出有效的质量控制措施。     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法

提出了一种新的计算弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法，它是一种时域复模态分析方法。利用此方法获得了弹性-粘弹性复合结构在白噪声、滤过白噪声等典型平稳随机激励下随机响应的各阶谱矩的解析表达式，分析了粘弹性对各阶谱矩的影响。此计算方法简便、易用，无论单自由度或多自由度系统均适用，为进一步研究弹性-粘弹性复合结构在随机激励下的可靠性打下良好基础。     

微带型Wilkinson功分器设计与实现

小型低功耗器件是射频电路设计的研究热点,而微带技术具有小型化低功耗的优点,为此在介绍微带型Wilkin-son功分器工作原理的基础上,使用基于矩量法的ADS软件设计、仿真和优化计算相关数据参数,并制作了一个微带功分器实例,最后对加工的样品进行实测,获得与仿真值吻合较好的预期结果。     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

发动机扭矩与转速关系经验公式试验研究

在对发动机外特性曲线扭矩与转速实验数据分析的基础上，对原有的经验公式进行了分析、改进，提出了新的经验公式．由这一经验公式所计算的数值，在最大扭矩与最大功率点之间，可与实验数据拟合得很好．与原经验曲线相比，新经验曲线与实验曲线的离差可下降50％以上．     

Stress State of Bent Buried Pipelines

The authors consider edge effects in buried pipelines that occur in the region of joining of a straight buried pipe and a bent insert (factory bend, elbow, or an elastically bent segment). The action of those effects results in the appearance of additional bending moments, which are proportional to the difference between the axial force in an infinite straight pipeline and that in a closed-end pipe, and depend on the geometrical parameters of the pipeline and physical-mechanical characteristics of the soil. Specific examples of analysis of elastic interaction of a pipeline with the soil for pipe bends with various radii of the bend arc are offered. It is shown that additional bending stresses may exceed appreciably the stresses from the axial force, and therefore, they should be taken into account when designing and building pipelines. The solution for an elastically bent segment has been obtained and analyzed.     

A method for multi-parameter PDF estimation of random variables

The probability distribution function (PDF) of a random variable Z is approximated with c·e^Q(z), where Q(z) is a polynomial function and c is normalizing constant. Based upon the weighted residual method, general linear algebraic equations have been derived for the evaluation of the unknown parameters in the polynomial. Numerical examples are presented and the results show that the PDFs obtained using the proposed method converge to those obtained from Monte Carlo simulation as the number of parameters in the approximate PDF increases.     

螺旋管簧的可靠性优化设计

讨论了螺旋管簧的可靠性优化设计问题。在基本随机变量的概率特性已知的情况下，采用二阶矩法和可靠性优化设计方法对螺旋管簧进行了可靠性优化设计。通过计算机程序可以直接实现螺旋管簧的可靠性优化设计，迅速准确地得到螺旋管簧的可靠性优化设计信息。