An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

采金船采选工艺流程病症诊治专家系统

应用专家系统理论，建立了采金船采选工艺流程病症诊治专家系统，此系统对于采金船采选工艺流程中存在的技术病症，具有诊断、治理及致因分析等功能．     

齿轮磨前滚刀的齿形研究

本文介绍了磨前滚刀滚切齿轮的最大根切量和磨后的渐开线长度计算,并建立了数学模型。为更加直观起见,还建立了模拟滚齿的数学模型。并在实验的基础上提出了参考标准。     

THE FLOW PRODUCED IN PARTICLE-SUSPENSION BY AN INFINITE ROTATING DISK:SERIES SOLUTION

To the flow produced in particle-suspension by a rotating disk of infinite extent,the asymptotic behavior at infinity is analyzed.A corresponding series solution is presented.It isshown that this approach yields widely valid solutions of high accuracy for all the cases in whichthat suction or weak injection at the disk surface exists.For the cases that strong injection or par-ticle-free band exists,the series method fails.     

汛期采金船的缆绳牵拉

本文介绍了采金船渡汛时的停泊方向及采金船在洪水中可能产生拖曳力的估算方法，为了防止采金船汛期发生溜船事故，建议采用缆绳牵拉固船的措施，以保障采金船的汛期安全。     

液压同步剪系统的设计

本文通过对蜂窝陶瓷载体成型过程的分析，指出在其成型过程中存在的问题，提出了采用液压同步剪解决这些问题的方法。论文分析了同步剪的工作原理，给出了其液压原理图及其设计特点。     

圆管流动的二次转捩

利用直接数值模拟方法求解N-S方程来研究空间发展的圆管转捩,计算中雷诺数Re选定为3000。在局部壁面引入的周期性吹吸(PSB)扰动作用下,圆管中首先出现了塞流结构,并向下游迁移,同时有稳定的流向条带结构形成;在塞流结构离开计算域后,随着扰动的不断发展,流向条带结构逐渐破裂失稳,圆管流动出现了第二次转捩,这是一种新的转捩形式,我们称之为“二次转捩”。     

开放式玻璃自动切割机计算机控制系统

文章介绍一种自行研制的玻璃自动切割机开放式计算机控制系统，并针对该切割机加工范围大、惯性大、动态精度要求高等特点，研究了一种智能适应型PID控制算法。现场测试表明，该系统在功能、性能和控制精度上达到或接近国外同类产品的先进水平，在系统硬件和软件的开放性上优于国外产品。文中详细介绍了该计算机控制系统的功能、系统设计、控制算法及其调试结果。     

10000m^3内浮顶油罐双浮动吸油装置设计

介绍了某油库扩建工程中10 000 m3内浮顶油罐双DN500浮动吸油装置的结构设计,并对内浮顶罐浮动吸油装置的浮力进行了优化配置,此经验对我国内浮顶油罐浮动吸油装置的设计和使用具有一定的指导意义.