Three-dimensional and anisotropic numerical analysis of a PEM fuel cell

In this study, the effects of cell temperature and relative humidity on charge transport parameters are numerically analyzed. In order to perform this analysis, three-dimensional and anisotropic numerical models are developed. The numerical models are integrated into the experimental values for anisotropic electrical conductivities, as depending on cell temperature and relative humidity, that were obtained from our previous study. The achieved results indicate that the values of current densities in the in-plane direction increase with increasing cell temperature and relative humidity, while the current densities reach a maximum in the rib regions for both the numerical model at the through-plane direction. The behaviors of electrolyte potentials are similar with changes in the cell temperature and relative humidity. In addition, the cathode electrical potentials in both the in-plane direction and through-plane direction do not change to a considerable amount with increasing cell temperature and relative humidity.     

隐蔽老火区立体式综合治理研究

对2320隐蔽老火区首先通过灌注泥浆对火区进行治理,同时对部分裂隙通道进行堵漏,然后对泥浆不能到达的区域注入高倍数三相泡沫灭火材料泡沫,瞬间将火源处覆盖,火源因隔绝氧气而窒息灭火。三相泡沫具有良好的堆积性和流动性,对煤体具有保水保湿,惰化遗煤氧化空间,并能够对松散煤体进行化学阻化,从本质上降低遗煤自然氧化速率,消灭了隐蔽老火区的火灾隐患,具有较高的推广价值。     

石油化工生产火灾危险性分析

针对石油化工生产的特点,从物料特性、上艺装置、工艺控制参数、防火防爆安全装置、作业性质和消防安全设施等几方面综合分析其火灾危险性,并提出相应的防范措施,为消防安全评价提供依据。     

抗洪抢险措施及效果

结合“９８”抗洪抢险实例，对多种险情作了具体分析，通过汛后调查，对抗洪抢险消险措施和效果进行了总结，为今后进一步做好防洪消险工作提供了经验。     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Thin hard coatings fracture propagation during the impact test

One of the most significant applications of the impact test is to investigate thin hard coatings fatigue properties. Herein the test conditions and duration up to the film damage initiation, are considered in order to determine the critical stresses associated with the coating fatigue strength. Moreover, the subsequent film damage propagation is a significant mechanism as well, since it refers to the ability of the coating to withstand loads after its fatigue damage initiation. In order to describe the film fracture propagation the failed area ratio was introduced and an algorithm to determine this magnitude developed, based on the analysis of imprint scanning electron microscopy graphs. The application of the coating failed area ratio will be demonstrated in various impact test film cases, also with superficial thin layers. The top layers do not affect, in general, the failure initiation of the basic coating. However, according to the obtained results, the superficial films influence the basic coating failure propagation rate during the impact test.     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

安徽省长江干堤的几种加固措施

安徽省境内765km的长江干堤，由于均是在原来旧堤的基础上经逐年加高培厚的，修筑时均未按设计要求施工，致使堤身密实度不够，新老堤土之间结合不牢，在汛期高水位时易产生渗漏。20世纪70年代以来，安徽省高度重视对长江干堤渗漏隐患的处理，经过长期的实践，逐渐摸索出一套行之有效的除险加固方法，如锥探灌浆、灭杀白蚁、冲抓套吉、垂直铺塑防渗、粘土铺盖及压渗盖重等处理措施。使长江干堤的渗漏隐患得以基本消除，其具体作法可供类似工程借鉴。     

A comparative study on the effect of VUV radiation in plasma SiOx-coated polyimide and polypropylene films

Wettability of polyimide (PI) and polypropylene (PP) films have been improved using SiO_x-like thin layers deposited from a mixture of hexamethyldisiloxane (HMDSO) and oxygen in a microwave distributed electron cyclotron resonance plasma reactor. The films wettability evolution behaviors were evaluated through the results of contact angle measurements, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The plasma depositions of SiO_x thin layers in presence of VUV radiation induce a contact angle decrease to about 7° and 35° for PI and PP films, respectively. XPS data showed that such difference in wettability is attributed to the increase of hydrophilic group's proportion at the surface of coated PI films due to VUV irradiation. AFM images showed that the PI surface topography remains relatively smooth when coated in presence of VUV radiation. However, in the case of PP films, AFM images revealed the growth of irregular structure due to a substrate etching effect supported by VUV radiation. For polymers coated without VUV irradiation, the deconvolution of the C1s peaks showed a significant decrease of CO bonds for both PI and PP substrates.