Cyberbullying: Effect of emergency perception on the helping tendencies of bystanders

The effect of the emergency perception of bystanders of cyberbullying victims on helping behaviors is often neglected in research on cyberbullying. In this study, we explored the influence of this cognitive factor on cyber-bystanders’ helping tendencies as well as elucidated possible underlying processes. The results of two studies were reported. In Study 1, 150 undergraduates read a true case of a girl experiencing cyberbullying. The results indicated that when the participants perceived the victim’s situation to be more critical (i.e., higher emergency perception), their helping tendencies were stronger, partly through increased state empathy followed by feelings of responsibility to help. In Study 2, we randomly assigned 300 undergraduates to two groups. The low emergency group read the same cyberbullying case as Study 1, whereas the cyberbullying case read by the high emergency group contained additional emergency information of the victim. The results indicated that the high emergency group expressed stronger helping tendencies than did the low emergency group. This effect was caused by a stronger perception that the victim was in an emergency situation, which not only strengthened the participants’ helping tendencies directly but also indirectly through increasing their state empathy and feelings of responsibility to help.     

Sealing behaviour of glass-based composites for oxygen transport membranes

In this study, seven different filler materials in different proportions were added to a Ba-Ca-Si glass matrix “H” to investigate new sealant with higher thermal expansion coefficient (CTE) value and good sealing performance for application in oxygen transport membrane (OTM). SrTi_0.75Fe_0.25O_3-δ (STF25) was used as an OTM, and the sealing partners were ferritic steel Aluchrom and pre-oxidized Aluchrom. Compatibility tests were carried out to investigate the feasibility of the composites. Higher CTE values were found in dilatometer tests on composite samples by adding 40 wt% Ag (HAg40) and 30 wt% Ni-Cr (HNC30). Gas-tightness measurements of sandwiched samples produced appropriate helium leakage rates in the range of 10^?6 mbar·l·s^?1. Sealing behaviour of sealants HAg40 and HNC30 were investigated by joining STF25 and as-delivered/pre-oxidized Aluchrom together. Scanning electron microscopy (SEM) on cross-sections of the joints revealed a homogeneous microstructure and good adherence of the glass sealants to support metals and STF25.     

Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Note of Caution for the Aqueous Behaviour of Metal-Based Drug Candidates

Poor aqueous solubility is one of the recurrent drawbacks of many compounds in medicinal chemistry. To overcome this limitation, the dilution of drug candidates from stock solutions of an organic solvent is common practice. However, the precise characterisation of these compounds in aqueous solutions is often neglected, leading to some uncertainties regarding the nature of the actual active species. In this communication, we demonstrate that two ruthenium complexes previously reported by our group for their chemotherapeutic potential against cancer, namely [Ru(DIP)₂(sq)](PF₆) and [Ru(DIP)₂(3-methoxysq)](PF₆), where DIP is 4,7-diphenyl-1,10-phenanthroline, sq=semiquinonate and 3-methoxysq=3-methoxysemiquinonate, form colloids in water-DMSO (1 % v/v) mixtures that are invisible to the naked eyes. [Ru(DIP)₂(3-methoxysq)](PF₆) was found to form a highly stable and monodispersed colloid with nanoaggregates of ∼25 nm. In contrast, [Ru(DIP)₂(sq)](PF₆) was found to form large reticulates of mostly spherical aggregates which size was found to increase over time. The difference in size and shape distribution of drug candidates is of tremendous significance as the study of their biological activity might be severely affected. Overall, we strongly believe that these observations should be taken into account by the scientific community working on the development of metal-based drugs with poor water solubility.     

Valorisation of potato wastes

Potato processing industry has a high degree of discarding, which currently has low added value being used primarily for animal feed. However, potato wastes offer a broad range of interesting components such as antioxidants, starch, protein or fibre with potential applications in the food and non-food industries. The recovery of these high valuable fractions using efficient multistage and multiproduct processes could be of great interest. This short review provides a general overview on the integral valorisation of potato wastes, offering an updated vision of the main residual parts generated during potato harvesting and processing, the high valuable obtained components focusing on the bioactive ones and the potential of the emerging extraction techniques over conventional ones. In addition, innovative applications are discussed to highlight the scientific and applied interest of these underutilised and undervalued fractions and to emphasise the integral valorisation of raw materials.     

Emergency egress for the elderly in care home fire situations

Practitioners are continuing to develop egress modelling software for the design of the built environment. These models require data about human behaviour and factors for calibration, validation and verification. This study aims to address the specific data and knowledge gap: emergency egress of the elderly. Such data are difficult to collect given privacy and consent concerns, with strong relationships generally being required between residences and researchers. Through the observation of nine fire drills at six Canadian long-term care (LTC) and retirement homes, specific evacuation actions and behaviour were observed for 37 staff members and information about the evacuation of 56 residents was collected. These drills demonstrated that emergency egress in LTC and retirement homes is highly staff dependent with 72% of residents recorded requiring full assistance at all stages of movement in evacuation, and that the type of announced/unannounced drill and level of resident care will affect the type of data collected. The development of travel speed and pre-movement is discussed subject to limitation with qualitative behavioural insights of residents that were observed. This study provides valuable methodological discussion on how to conduct behavioural studies in similar highly restricted research environments. Specific attention is given to understanding the considerations that must be made when using fire drills as data sources, and the impact that these can have on using such data for modelling. This study may inform the initial setup and programming of evacuation models from an actions and behavioural perspectives of staff members and residents.     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

Fatigue limit evaluation of various martensitic stainless steels with new robust thermographic data analysis

Thermography represents an important tool to study fatigue behaviour of materials.In this work, the fatigue limit of martensitic and precipitation hardening stainless steels has been determined with thermographic methods. Despite their use in corrosive and cryogenic environments, there is a data lack in literature concerning the study of fatigue behaviour.The peculiarity of these materials is the brittle behaviour: therefore, during fatigue tests the characteristic small deformations determine small changes of temperature. Thus, to properly determine the fatigue limit of aforementioned stainless steels, a more accurate setup is necessary in order to correctly detect surface temperature of specimens due to dissipation heat sources.In literature, different procedures have already been proposed to evaluate the fatigue limit from thermal data but very few works lead to an early detection of dissipation process which can obtain a further reduction of overall testing time. The aim of the paper is to propose a new robust thermal data analysis procedure for estimating fatigue limit of stainless steels in automatable way.     

Sintering behaviour of fluorapatite–silicate composites produced from natural fluorapatite and quartz

In this work, the sintering behaviour of fluorapatite (FAp)–silicate composites prepared by mixing variable amounts of natural quartz (2.5 wt% to 20 wt%) and FAp was studied. The composites were pressureless sintered in air at temperatures from 1000 °C to 1350 °C. The effects of temperatures on the densification, phase formation, chemical bonding and Vickers hardness of the composites were evaluated. All the samples exhibited mixed phase, comprising FAp and francolite as the major constituents along with some minor phases of cristobalite, wollastonite, dicalcium silicate and/or whitlockite dependent on the quartz content and sintering temperature. The composite containing 2.5 wt% quartz exhibited the best sintering properties. The highest bulk density of 3 g/cm³ and a Vickers hardness of >4.2 GPa were obtained for the 2.5 wt% quartz–FAp composite when sintered at 1100 °C. The addition of quartz was found to alter the microstructure of the composites, where it exhibited a rod-like morphology when sintered at 1000 °C and a regular rounded grain structure when sintered at 1350 °C. A wetted grain surface was observed for composites containing high quartz content and was believed to be associated with a transient liquid phase sintering.