Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Semiconductor particles doped Al₂O₃ coatings were prepared by cathode plasma electrolytic deposition in Al(NO₃)₃ electrolyte dispersed with SiC micro- and nano-particles (average particle sizes of 0.5–1.7?µm and 40?nm respectively). The effects of the concentrations and particle sizes of the SiC on the microstructures and tribological performances of the composite coatings were studied. In comparison with the case of dispersing with SiC microparticles, the dispersion of SiC nanoparticles in the coatings was more uniform. When the concentration of SiC nanoparticles was 5?g/L, the surface roughness of the composite coating was reduced by 63%, compared with that of the unmodified coating. Friction results demonstrated that the addition of 5?g/L SiC nanoparticles reduced the friction coefficient from 0.60 to 0.38 and decreased the wear volume under dry friction. The current density and bath voltage were measured to analyze the effects of SiC particles on the deposition process. The results showed that the SiC particles could alter the electrical behavior of the coatings during the deposition process, weaken the bombardment of the plasma, and improve the structures of the coatings.     

Corrosion behavior of under‐, peak‐, and over‐aged 6063 alloy: A comparative study

The mechanical property of age‐hardenable Al‐alloys is governed by the state of ageing, which determines the microstructure and consequently, their corrosion behavior which is a vital aspect for a number of applications. This article presents a comparative assessment of corrosion behavior of under‐, peak‐ and over‐aged Al‐Mg‐Si alloy. Corrosion characteristics have been determined via immersion tests in 0.1 M ortho‐phosphoric acid solution and intergranular corrosion (IGC) tests. Corroded surfaces are examined by field emission scanning electron micrographs‐energy dispersive spectroscopy and 3D optical profilometer. The obtained results reveal that the corrosion rate at a specific immersion time as well as the depth of IGC increases in the order for under‐, peak‐, and over‐aged states. Irrespective of the state of ageing, corrosion loss increases linearly but the rate of corrosion decreases rapidly with increasing immersion time. The dominant mode of corrosion in under‐aged alloy is identified as localized pitting, while peak‐aged is highly susceptible to IGC in contrast extensive pitting corrosion is observed for over‐aged alloy. The observed differences in corrosion behavior are explained considering characteristics of precipitates. Formation of β (Mg₂Si) in case of over‐aged alloy and presence of inclusions like AlFeMnSi particles are found to accelerate pitting corrosion.     

Estimation of the Stress-Strength Reliability for Exponentiated Pareto Distribution Using Median and Ranked Set Sampling Methods

In reliability analysis, the stress-strength model is often used to describe the life of a component which has a random strength (X) and is subjected to a random stress (Y). In this paper, we considered the problem of estimating the reliability R=P [Y<X] when the distributions of both stress and strength are independent and follow exponentiated Pareto distribution. The maximum likelihood estimator of the stress strength reliability is calculated under simple random sample, ranked set sampling and median ranked set sampling methods. Four different reliability estimators under median ranked set sampling are derived. Two estimators are obtained when both strength and stress have an odd or an even set size. The two other estimators are obtained when the strength has an odd size and the stress has an even set size and vice versa. The performances of the suggested estimators are compared with their competitors under simple random sample via a simulation study. The simulation study revealed that the stress strength reliability estimates based on ranked set sampling and median ranked set sampling are more efficient than their competitors via simple random sample. In general, the stress strength reliability estimates based on median ranked set sampling are smaller than the corresponding estimates under ranked set sampling and simple random sample methods.     

Application of Vis–NIR hyperspectral imaging in classification between fresh and frozen-thawed pork Longissimus Dorsi muscles

Fresh and frozen-thawed (F-T) pork meats were classified by Vis–NIR hyperspectral imaging. Eight optimal wavelengths (624, 673, 460, 588, 583, 448, 552 and 609 nm) were selected by successive projections algorithm (SPA). The first three principal components (PCs) obtained by principal component analysis (PCA) accounted for over 99.98% of variance. Gray-level-gradient co-occurrence matrix (GLGCM) was applied to extract 45 textural features from the PC images. The correct classification rate (CCR) was employed to evaluate the performance of the partial least squares-discriminate analysis (PLS-DA) models, by using (A) the reflected spectra at full wavelengths and (B) those at the optimal wavelengths, (C) the extracted textures based on the PC images, and (D) the fused variables combining spectra at the optimal wavelengths and textures. The results showed that the best CCR of 97.73% was achieved by applying (D), confirming the high potential of textures for fresh and F-T meat discrimination.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

数字化正弦平方脉冲信号

依据正弦平方脉冲的数学方程及其频谱分布，分别导出了与理想和标称视频带宽相对应的正弦平方脉冲的数学表达式及其编程生成方法。实验表明，此法不仅精确，而且便于修改参数，并可直接读人数字电视系统，来测定视频线性响应。     

红外光谱法用于快速测定车用柴油酸度等性质的研究

针对车用柴油酸度等性质测定过程繁琐，采用衰减全反射样品池测定车用柴油的红外光谱，用偏最小二乘法（PLS）建立红外光谱测定车用柴油酸度、密度、闪点和凝点的4个校正模型，验证标准误差分别为0.46 mg/(100 mL),0.77kg/m3,2.60 ℃,2.77 ℃，该方法符合标准方法再现性要求。与标准方法相比，该方法具有无需预处理、操作简单、测量快速、重复性好等优点。     

新型高K栅介质ZrO2薄膜材料的制备及表征

采用超高真空电子束蒸发法制备了新型高 K栅介质-非晶 ZrO2薄膜. X射线光电子能谱 (XPS) 中 Zr3d5/2 和 Zr3d3/2 对应的结合能分别为 182.1eV和 184.3eV, Zr元素的主要存在形式为 Zr4+,说明薄膜由完全氧化的 ZrO2组成 ,并且纵向分布均一.扩展电阻法( SRP)显示 ZrO2薄膜的 电阻率在 108Ω@ cm以上,通过高分辨率透射电镜( HR- XTEM)可以观察 ZrO2/Si界面陡直,没有 界面反应产物 ,证明 600℃快速退火后 ZrO2薄膜是非晶结构.原子力显微镜( AFM)表征了薄膜的 表面粗糙度,所有样品表面都很平整,其中 600℃快速退火样品 (RTA)的 RMS为 0.480nm.     

Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.