Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

基于Matlab与VC混合编程的研究

针对Matlab和Visual C^ 应用的特点，讨论了在VC中调用Matlab的3种方法，着重介绍了利用Matcom和Matlab编译器进行混合编程的方法和步骤，为开发处理大量数据的应用程序提供了依据。     

编译错误的一种处理策略

本文提出了一种独特的编译错误处理方法，其特点是将错误信息组成一个独立的文件。     

大型储罐基础非平面倾斜问题的探讨

大型储罐因基础产生非平面倾斜而影响其正常使用的情况在工程中时有发生,文章通过对某油罐工程中基础沉降观测结果的分析,探讨了储罐基础产生非平面倾斜的原因。相邻储罐之间的相互影响、充水预压未达到规范要求以及地基处理措施不当是引起储罐基础非平面倾斜的主要因素。针对相邻储罐间的相互影响,根据现行《石油化工企业设计防火规范》和《石油化工企业钢储罐地基与基础设计规范》的规定,提出以下建议:储罐布置的净距除应满足防火规范规定外,有条件时也应适当考虑对基础沉降的影响,当采用复合地基时,相邻储罐间的净距不宜小于0.6 D;当占地面积成为主要矛盾,储罐间的净距只能限制在防火规范规定的最小范围时,在地基处理时就应采取有效措施,以尽可能减少相邻储罐的相互影响。     

C语言编程在智能化重力加速度测试仪中的应用

在基于单片机的智能化重力加速度测试仪中采用Ｃ语言编程简化了程序设计任务，对于汇编语言难于处理的浮点数运算及汉字打印输出可通过Ｃ语言编译器的内部库函数调用实现，介绍了一种专为８０５１系列单片机设计的Ｃ语言编译器Ｆｒａｎｋｉｌｉｎ Ｃ５１，它具有代码优化功能，能产生极高效率的机器码，并且提供了丰富的内部函数库。描述了Ｃ５１函数库所支持的ＩＥＥＥ标准浮点数的内存格式以及采用ｓｐｒｉｎｔｆ（）函数处理包括     

Compile-time copy elimination

Single-assignment and functional languages have value semantics that do not permit side-effects. This lack of side-effects makes automatic detection of parallelism and optimization for data locality in programs much easier. However, the same property poses a challenge in implementing these languages efficiently. This paper describes an optimizing compiler system that solves the key problem of aggregate copy elimination. The methods developed rely exclusively on compile-time algorithms, including interprocedural analysis, that are applied to an intermediate data flow representation. By dividing the problem into update-in-place and build-in-place analysis, a small set of relatively simple techniques—edge substitution, graph pattern matching, substructure sharing and substructure targeting—was found to be very powerful. If combined properly and implemented carefully, the algorithms eliminate unnecessary copy operations to a very high degree. No run-time overhead is imposed on the compiled programs.     

微絮凝接触过滤处理低浊度含藻水的研究

通过现场试验，对微絮凝过滤处理生活用水所带来的一系列问题进行了详细、科学的分析，在大量试验数据基础上对产生问题的原因进行了研究并取得了初步结论。在此基础上，提出了改进措施，取得了实效。     

沪芦高速公路软土地基设计与研究

软土地基的处理是影响高等级公路工程质量和使用性能的重要因素 ,针对沪芦高速公路的工程特点 ,通过对不同土层力学性能分析 ,地基稳定验算以及沉降计算提出地基处理方案 ,并介绍通过地基处理后获得的显著效果     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。