On the origin of strain hardening in glassy polymers

The influence of network density on the strain hardening behaviour of amorphous polymers is studied. The network density of polystyrene is altered by blending with poly(2,6-dimethyl-1,4-phenylene-oxide) and by cross-linking during polymerisation. The network density is derived from the rubber-plateau modulus determined by dynamic mechanical thermal analysis. Subsequently uniaxial compression tests are performed to obtain the intrinsic deformation behaviour and, in particular, the strain hardening modulus. At room temperature, the strain hardening modulus proves to be proportional to the network density, irrespective of the nature of the network, i.e. physical entanglements or chemical cross-links. With increasing temperature, the strain hardening modulus is observed to decrease. This decrease appears to be related to the influence of thermal mobility of the chains, determined by the distance to the glass-transition temperature (T−T_g).     

Accurate estimation of capacities and cross-traffic of all links in a path using ICMP timestamps

The estimation of the link capacity and its available bandwidth in an end-to-end path is crucial for network management, admission control and flow control for adaptive applications. This paper introduces an estimation mechanism able to accurately estimate the available bandwidth of all links in an end-to-end path, through its capacity and cross-traffic estimation. The estimation procedures resort to the dispersions of packet pairs and trains using the concepts of ICMP Timestamp and Traceroute that, efficiently used together, enable the measurement of the dispersions in all links in the path. These mechanisms were evaluated through simulation experiments, where we analyzed the influence of the several network parameters on each estimation mechanism. The results show that these estimation methods are able to accurately estimate both the capacity and the cross-traffic of all links in a path with moderate length and with low overhead.     

基于矢量平均的信道估计算法

提出一种适用于DS-CDMA无线通信系统的低计算量而性能良好的信道估计算法。在DS-CDMA系统中，当接收信号经过解扩或多用户检测等时域预处理后，可以认为干扰大大减弱、期望信号在处理后的信号中占主要地位。这样，用预处理后信号相关阵的最大特征值对应的特征矢量可以很好地近似期望信号的信道矢量。但是，直接特征分解需要很大的计算量，特征跟踪计算量较低，但瞬态性能较差。本文提出一种基于相关矩阵列矢量平均的信道估计算法，该算法不需要特征分解或跟踪。仿真结果表明：新算法在降低计算量的情况下可以获得同直接特征分解方法几乎相同的性能。     

An original approximate method for estimating the invariant probability distribution of a large class of multi-dimensional nonlinear stochastic oscillators

This paper proposes an original method for obtaining analytical approximations of the invariant probability density function of multi-dimensional Hamiltonian dissipative dynamic systems under Gaussian white noise excitations, with linear non-conservative parts and nonlinear conservative parts. The method is based on an exact result and a heuristic argument. Its pertinence is attested by numerical tests.     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

异步DS-CDMA系统中基于矩阵点除算法的DOA估计

针对异步DS-CDMA系统中的多用户环境,本文提出了一种低复杂度的DOA估计算法——矩阵点除算法。该算法通过对感兴趣信息的逐次分离,实现了DOA的逐路径估计。算法具有两方面显著优势:(1)克服了传统的DOA估计算法在路径总数大于天线阵元数时不能工作这一缺陷:(2)避免了计算复杂的特征值分解运算,大大降低了算法复杂度。仿真实验验证了算法的有效性。     

火工品压药机装配误差的研究

针对军用雷管生产线中压药机结构,分别用极值法和概率法对压药机冲子和雷管的配合精度,进行了装配尺寸链的描述和计算,并对所得的结果进行了比较。     

基于EDGE系统信道估计实现方案的研究

研究了基于ＥＤＧＥ系统接收机中信道估计的实现方案，并对算法的各项性能做出评估。首先论述了算法的采用及其理论依据。接着，说明了信道预估计的原理及方法。最后，针对ＭＡＴ－ＬＡＢ及 ＤＳＰ上的仿真结果，比较了各项系数对于系统性能改善所具有的影响和作用，对系统特性作了较为详细的分析总结。