烧结机卸料装置耐磨性改善

烧结机导料箱、单辊破碎机和卸料漏斗承载着烧结热矿的导料、破碎与输送,是烧结生产的重要组成部分。高温、重载的工况环境决定着机尾卸料装置必须具有抗磨损、耐高温的特性。针对邯钢1^#435m^2烧结机机尾关键部件耐磨工作面寿命短,更换不方便等问题,分析磨损机理与失效原因,提出改进抗磨工作面结构,升级耐磨材料,优化焊接工艺等措施。通过技术方案的实施,使烧结机导料箱、单辊破碎机和卸料漏斗等卸料装置维持了较高的抗磨损性能,达到了预期的改造效果。     

On the thermally-induced seizure in bearings: A review

This paper presents a state-of-the-art survey of papers reported on the nature of a troublesome failure mode in bearings known as seizure. This mode of failure is thermally-induced and it occurs in both journal and rolling element bearings. To gain insight, particular attention is given to reported experimental observation, various mechanisms involved, and available prediction methodologies.     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

线切割加工轧辊孔型模板提高精度的方法

详细论述了利用线切割机加轧辊孔型模板中易出现的几种影响加工精度的因素及消除方法，以达到提高模板精度。     

轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

Dynamics of Vibroprotective Systems with Roller Dampers of Low-Frequency Vibrations

We study low-frequency vibrations of a vibroprotective system of solid bodies formed by a roller damper and a moving load-carrying body under the action of external harmonic excitations. The dynamic equations of combined motion of the working body of the damper over the hinged roller without sliding and the load-carrying body are deduced and numerically analyzed. A new procedure is proposed for the evaluation of the optimal parameters of adjustment of roller dampers in nonlinear systems.     

High-load, squeeze action linear bearings with beam deflection

The literature provides little information on high-speed, high-normal-load, plain linear bearings, although the case for two rigid surfaces in relative linear motion can readily be solved by assuming squeeze action resistance. A new genus of internal combustion engines based on the Stiller-Smith mechanism incorporates connecting rods constrained by linear bearings, with the central normal load on the rod restricted by an oil film. A general analysis takes into account the bending of the rod, when the distributed oil film pressure resists the distributed load on the elastic rod. Design charts result that yield the dimensionless velocity at which the rod sinks in the oil as a function of the dimensionless load and the bearing clearance, and predict the deflection of the beam. The rod clearance history simulations for the Stiller-Smith engine compare favourably with computations for the rigid beam, confirming the analysis technique.     

用φ76 mm穿孔机组生产φ63mm毛管的设备改进

介绍了用Φ76mm穿孔机组生产Φ63mm毛管的设备概况及其改进。改进后，Φ76mm穿孔机组增加了产品范围为后面的冷技工序减少了拉拔道次，从而降低了Φ51mm以下冷拔管的生产成本。     

直缝焊管机组生产冷弯型钢产品初探

主要介绍了φ２１９直缝焊管机组生产高速公路护栏 成型原理、工艺布置、变形方式、变形图和轧辊设计。