钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Economic growth,CO2 emissions,and energy consumption in the five ASEAN countries

This paper investigates the relationship between economic growth, carbon dioxide (CO₂) emissions, and energy consumption with an aim to test the validity of the Environmental Kuznets Curve (EKC) hypothesis in five ASEAN (Association of South East Asian Nations) countries (Indonesia, Malaysia, Philippines, Singapore, and Thailand) by applying the panel smooth transition regression (PSTR) model as a new econometric technique. The PSTR model is more flexible and appropriate for describing cross-country heterogeneity and time instability. Our empirical results strongly rejected the null hypothesis of linearity, and the test for no remaining nonlinearity indicated a model with one transition function and two threshold parameters. The first regime (levels of GDP per capita below 4686 USD) showed that environmental degradation increases with economic growth while the trend was reversed in the second regime (GDP per capita above 4686 USD). The results also showed that energy consumption with either the first or the second regime lead to increase CO₂. The overall results support the validity of the EKC hypothesis in the ASEAN countries.     

A Lattice Approach to Image Segmentation

After a formal definition of segmentation as the largest partition of the space according to a criterion σ and a function f, the notion of a morphological connection is reminded. It is used as an input to a central theorem of the paper (Theorem 8), that identifies segmentation with the connections that are based on connective criteria. Just as connections, the segmentations can then be regrouped by suprema and infima. The generality of the theorem makes it valid for functions from any space to any other one. Two propositions make precise the AND and OR combinations of connective criteria. The soundness of the approach is demonstrated by listing a series of segmentation techniques. One considers first the cases when the segmentation under study does not involve initial seeds. Various modes of regularity are discussed, which all derive from Lipschitz functions. A second category of examples involves the presence of seeds around which the partition of the space is organized. An overall proposition shows that these examples are a matter for the central theorem. Watershed and jump connection based segmentations illustrate this type of situation. The third and last category of examples deals with cases when the segmentation occurs in an indirect space, such as an histogram, and is then projected back on the actual space under study. The relationships between filtering and segmentation are then investigated. A theoretical chapter introduces and studies the two notions of a pulse opening and of a connected operator. The conditions under which a family of pulse openings can yield a connected filter are clarified. The ability of segmentations to generate pyramids, or hierarchies, is analyzed. A distinction is made between weak hierarchies where the partitions increase when going up in the pyramid, and the strong hierarchies where the various levels are structured as semi-groups, and particularly as granulometric semi-groups. The last section is based on one example, and goes back over the controversy about “lattice” versus “functional” optimization. The problem is now tackled via a case of colour segmentation, where the saturation serves as a cursor between luminance and hue. The emphasis is put on the difficulty of grouping the various necessary optimizations into a single one.     

开关电源的平均电流自动均流技术

针对多个开关电源并联时易出现负载电流在各模块间分配不均的现象,介绍了常用的负载电流自动均流法——平均电流自动均流法及其工作特性。并针对其存在母线电压降低的缺陷,提出了一种改进的平均电流自动均流方法,经试验证明均流精度比较高。     

Evaluation of performance enhancing proxies in internet over satellite

Performance enhancing proxies (PEPs) are widely used to improve the performance of TCP over high delay‐bandwidth product links and links with high error probability. In this paper we analyse the performance of using TCP connection splitting in combination with web caching via traces obtained from a commercial satellite system. We examine the resulting performance gain under different scenarios, including the effect of caching, congestion, random loss and file sizes. We show, via analysing our measurements, that the performance gain from using splitting is highly sensitive to random losses and the number of simultaneous connections, and that such sensitivity is alleviated by caching. On the other hand, the use of a splitting proxy enhances the value of web caching in that cache hits result in much more significant performance improvement over cache misses when TCP splitting is used. We also compare the performance of using different versions of HTTP in such a system. Copyright © 2003 John Wiley & Sons, Ltd.     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

韶钢4号高炉顺行状况的操作技术

对韶钢炼铁厂4号高炉炉况和操作上存在的问题进行了分析,主要原因是原材料质量较差,精料水平低,同时,高炉操作不能完全适应原材料条件.按照上稳下活工艺的原则,采取合理鼓风动能、活跃炉缸工作状态、稳定热制度、合理中部冷却强度、炉顶小高压操作以及使用上部调节手段等一系列措施,使高炉的炉况顺行得到了较大的改善,各项主要技术经济指标取得相应的进步.2001年利用系数达3.024 t/m3·d,焦比达441 kg/t.     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

广州中城广场主体工程施工技术

广州中城广场工程结构形式复杂，平面曲折多角。施工中在应用多种模板体系、泵送混凝土、无粘结预应力楼板及核心筒部分小平台滑模等方面，采用了多项新技术，保证了工程质量，加快了工程进度。     

TN-S系统接地方式中重复接地的探讨

通过对TN S系统接地方式中重复接地的探讨 ,介绍了重复接地对N线和PE线的不同作用 ,明确了TN S系统接地方式中重复接地的设计和施工方法。