钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Electricity Production

Current data on net electricity production, as well as a breakdown of production by country. Updated on a monthly basis.     

Electricity Production

Current data on net electricity production, as well as a breakdown of production by country. Updated on a monthly basis.     

Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

Animations showing Lego manipulative tasks: Three potential moderators of effectiveness

Evidence suggests that transient visual information, such as animations, may be more challenging to learn than static visualizations. However, when a procedural-manipulative task is involved, our evolved embodied cognition seems to reverse this transitory challenge. Hence, for object manipulative tasks, instructional animations may be more suitable than statics. We investigated this argument further by comparing animations with statics using a Lego task shown to university students, by examining three potential moderators of effectiveness: (a) the environment of manipulation (virtual or physical), (b) the quality of visual information (focused or unfocused), and (c) the presence of hands (no hands or with hands). In Experiment 1 we found an advantage of animation over statics, and no differences among the environments. In Experiment 2, we again observed an animation advantage, a small advantage of focused static information compared to unfocused static information, and a positive effect of not showing the hands.     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

沙漠地区高精度地震资料处理技术

受静校正及各种类型干扰的影响,西部沙漠地区地震资料的高精度处理较东部地区有更大的难度。对准噶尔盆地中部Ⅱ区、Ⅲ区、Ⅳ区、顺托果勒等区块地震资料在振幅恢复、静校正、去除各类噪音、高精度速度分析及叠前、叠后子波处理等方面进行了大量的试验与研究,形成了较为系统的高精度地震资料处理技术,在西部不同区块地震资料处理中取得了较好的应用效果。     

Measurement and Identification of the Parameters of SPICE-Models of a Bipolar Transistor

A method of measuring and identifying the static parameters of a bipolar transistor is considered. The characteristic of the transistor, from which the parameters of the model are determined, is chosen depending on what group the calculated parameters belong to. The characteristics are measured in such a way that the equations of the model describing them can be reduced to the simplest form.     

Mixed Mode VLSI Implementation of a Neural Associative Memory

A mixed mode digital/analog special purpose VLSI hardware implementation of an associative memory with neural architecture is presented. The memory concept is based on a matrix architecture with binary storage elements holding the connection weights. To enhance the processing speed analog circuit techniques are applied to implement the algorithm for the association. To keep the memory density as high as possible two design strategies are considered. First, the number of transistors per storage element is kept to a minimum. In this paper a circuit technique that uses a single 6-transistor cell for weight storage and analog signal processing is proposed. Second, the device precision has been chosen to a moderate level to save area as much as possible. Since device mismatch limits the performance of analog circuits, the impact of device precision on the circuit performance is explicitly discussed. It is shown that the device precision limits the number of rows activated in parallel. Since the input vector as well as the output vector are considered to be sparsely coded it is concluded, that even for large matrices the proposed circuit technique is appropriate and ultra large scale integration with a large number of connection weights is feasible.     

等偏移距自动初至静校正

茅金根 ,梁秀文 ,杨午阳 ,冯有奎 .等偏移距自动初至静校正 .石油地球物理勘探 ,2 0 0 2 ,37(5 ) :4 6 9～ 4 72　　本文提出一种自动计算静校正量的新方法。它首先在等偏移距道集内对相邻道的初至波采用高精度相关构建一个关于炮、检时差的超大矩阵方程 ,然后采用优化统计迭代算法求解炮点和检波点的静校正量 ,并用概率分布函数确定精确的炮、检静校正量 ,最后用误差校正函数消除炮、检静校正误差。实际资料处理结果表明 ,本方法自动、省时、精度高。