裂解炉炉管基于风险的检验

管式裂解炉炉管受炉内高温及管内介质压力的共同作用,易发生蠕变等现象,因此,对裂解炉炉管进行风险评价尤为重要。应用API 581基于风险的检验规范对炉管的失效可能性及失效后果分别进行定量计算,并由此得到裂解炉炉管的定量风险结果和基于风险的检验周期,为裂解炉的风险控制与管理提供依据。     

细节决定采输卤的成败

通过认真学习《细节决定成败》，结合井矿盐开采的实际，分别以生产过程中的三个细节为主，讨论了在采输卤生产技术控制中的细节的重要性。     

可控震源施工中电台数据传输不良的原因分析及排除

可控震源在施工中,常常出现各种电台干扰,导致震源数据传输不正常或震源收不到仪器发出的遥控启动信号,影响正常施工.本文介绍了各种电台干扰引起的故障现象,分析了故障产生的原因,给出了故障的排除方法.     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

超高分子量聚乙烯的辐照效应

通过密度测定和ＤＳＣ热分析，观测了超高分子量聚乙烯的辐射效应。实验结果表明：在吸收剂量０—１．１３ＭＧｙ范围内，密度随吸收剂量的增加而增大，熔化热和熔点也有所增加，特别是在低剂量范围内增加十分明显。以上结果都说明，超高分子量聚乙烯在辐照过程中，结晶在完善或有新的结晶形成     

压差式漏率测试仪的实验研究

将薄膜电容真空计的测量室接于被测密闭容器，静态真空室接于一个比较容器，即组成一台压差式漏率测试仪。首先使两容器压力平衡，真空计读数为零。当被测容器存在漏孔时，真空计薄膜两侧形成压差，真空计指示读数，继而计算出该容器的漏率。应用商品真空计在抽真空测试时，检测的最小可测漏率达10－4～10-5Pa·L／s；而在充压测试时，因受气体温度变化的影响，灵敏度会降低几个量级。该仪器有可能具备寻找漏孔位置和确定漏孔漏率的功能。     

换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。     

系统备份及其误区分析

文章对系统备份的几个主要方面进行了讨论，并在此基础上，对系统备分的若干认识误区进行了分析。     

合成氨中置锅炉的修复

本文在分析中置锅炉失效原因的基础上，提出了详细的修复措施，为类似情况的设备修复提供了借鉴。     

半导体芯片厂有害气体检测器使用经验之探讨

本文除概略介绍气体检测器的种类处，主要对气体检测器的原理和在实际使用中的局限性作一基本归纳叙述。限于篇幅，本文将论述的重点放在气体检测器的选用与设置规划上，提出个人的一点心得与看法，以作为未来设置气体检测器系统时之参考。