| 圆弧槽流体动压型机械密封的性能研究 |
| |
| 引用本文： | 于明彬,孟祥铠,白少先,彭旭东,盛颂恩. 圆弧槽流体动压型机械密封的性能研究[J]. 润滑与密封, 2009, 34(9). DOI: 10.3969/j.issn.0254-0150.2009.09.008 |
| |
| 作者姓名： | 于明彬 孟祥铠 白少先 彭旭东 盛颂恩 |
| |
| 作者单位： | 1. 浙江工业大学过程装备及其再制造教育部工程研究中心,浙江杭州,310032
2. 浙江工业大学过程装备及其再制造教育部工程研究中心,浙江杭州,310032;浙江工业大学机械工程学院,浙江杭州,310032 |
| |
| 基金项目： | 国家自然科学基金资助项目，浙江省科技计划资助项目，浙江省高校中青年学科带头人专项基金 |
| |
| 摘 要： | 以核主泵用圆弧槽流体动压机械密封为研究对象,建立了端面液膜压力控制方程,应用有限元法分析了稳态工况下圆弧槽几何结构参数对密封性能参数的影响,以在较高液膜刚度条件下获得较低泄漏量为几何参数的优化准则,得到了密封具有优良综合性能的几何参数优选范围.结果表明:当槽深比为2.0～6.0,槽数为8～24,槽宽范围在0.75 mm至端面外内半径之差的1/2,圆弧槽内半径小于和等于时端面外内半径之差的1/2时,密封具有优良综合工作性能.
|
| 关 键 词： | 机械密封 圆弧槽 流体动压 结构设计 |
Analysis of a Hydrodynamic Face Seal with Circular Grooves onto Its Surface |
| |
| Yu Mingbin,Meng Xiangkai,Bai Shaoxian,Peng Xudong,Sheng Songen. Analysis of a Hydrodynamic Face Seal with Circular Grooves onto Its Surface[J]. Lubrication Engineering, 2009, 34(9). DOI: 10.3969/j.issn.0254-0150.2009.09.008 |
| |
| Authors: | Yu Mingbin Meng Xiangkai Bai Shaoxian Peng Xudong Sheng Songen |
| |
| Affiliation: | 1.The MOE of Engineering Research Center of Process Equipment and Its Re-manufacturing;Zhejiang University of Technology;Hangzhou Zhejiang 310032;China;2.College of Mechanical Engineering;China |
| |
| Abstract: | A mathematic model was set up to get film pressure between two faces of a hydrodynamic mechanical seal with circular grooves onto its surface for a primary coolant pump.Finite element analyse method was used to analyze sealing performances varying with geometric structure parameters under steady-state conditions.The optimum geometric parameters were presented based on the criterion of getting large film stiffness or opening force while maintaining reasonable leakage.The results show that such a seal is exce... |
| |
| Keywords: | mechanical seals circular arc grooves hydrodynamic geometric design |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
|
