| 镀铜/镍烧结钕铁硼永磁体与DP1180钢钎焊接头的组织与性能 |
| |
| 引用本文： | 苏金龙,罗萃,阮野,邱小明,邢飞.镀铜/镍烧结钕铁硼永磁体与DP1180钢钎焊接头的组织与性能[J].稀有金属材料与工程,2024,53(2):365-370. |
| |
| 作者姓名： | 苏金龙 罗萃 阮野 邱小明 邢飞 |
| |
| 作者单位： | 吉林大学 汽车材料教育部重点实验室，吉林 长春 130022;吉林大学 深圳研究院，广东 深圳 518057,上海航天控制技术研究所，上海 201109,吉林大学 汽车材料教育部重点实验室，吉林 长春 130022,吉林大学 汽车材料教育部重点实验室，吉林 长春 130022,吉林大学 汽车材料教育部重点实验室，吉林 长春 130022;吉林大学 深圳研究院，广东 深圳 518057 |
| |
| 基金项目： | Creation and Development technology project of Shenzhen, China (NO. 2021Szvup050), Shanghai Sailing Program （No. 23YF1417400）and 2020 Renewal Program of Jilin University (419080520464). |
| |
| 摘 要： | 采用Zn-6Sn-5Bi钎料对镀Cu/Ni的烧结NdFeB永磁体和DP1180钢进行钎焊连接，对比分析了2种镀层条件下钎焊接头的微观组织和力学性能。结果表明，对于镀Cu的烧结NdFeB永磁体和DP1180钢的钎焊接头，Cu在钎料中扩散并与Zn、Fe反应生成脆性金属间化合物，导致钎缝中出现裂纹和孔洞。与无镀层时的烧结NdFeB永磁体和DP1180钢的钎焊接头相比，接头的剪切强度由61.9 MPa降低至52.3 MPa；对于镀Ni的烧结NdFeB永磁体和DP1180钢的钎焊接头，Ni集中分布在NdFeB一侧的界面处，并且由于Sn和Bi的扩散形成了不同的扩散层，其剪切强度提高至78.1 MPa。
|
| 关 键 词： | 烧结NdFeB永磁体 金属镀层 钎焊接头 微观组织 剪切强度 |
| 收稿时间： | 2023/8/21 0:00:00 |
| 修稿时间： | 2023/9/21 0:00:00 |
Microstructure and Properties of Soldered Joints of Cu/Ni- Coated Sintered-NdFeB Permanent Magnets and DP1180 Steel |
| |
| Su Jinlong,Luo Cui,Ruan Ye,Qiu Xiaoming and Xing Fei.Microstructure and Properties of Soldered Joints of Cu/Ni- Coated Sintered-NdFeB Permanent Magnets and DP1180 Steel[J].Rare Metal Materials and Engineering,2024,53(2):365-370. |
| |
| Authors: | Su Jinlong Luo Cui Ruan Ye Qiu Xiaoming and Xing Fei |
| |
| Affiliation: | Key Laboratory of Automobile Materials Ministry of Education, Jilin University, Changchun 130022, China;Shenzhen Research Institute of Jilin University, Shenzhen 518057, China,Shanghai Aerospace Control Technology Research Institute, Shanghai 201109, China,Key Laboratory of Automobile Materials Ministry of Education, Jilin University, Changchun 130022, China,Key Laboratory of Automobile Materials Ministry of Education, Jilin University, Changchun 130022, China,Key Laboratory of Automobile Materials Ministry of Education, Jilin University, Changchun 130022, China;Shenzhen Research Institute of Jilin University, Shenzhen 518057, China |
| |
| Abstract: | Zn-6Sn-5Bi alloy was used to solder DP1180 steel and NdFeB permanent magnet coated with Cu and Ni, and the microstructures and mechanical properties of the soldered joints under different coating conditions were compared and analyzed. Results show that for the soldered joint of sintered NdFeB permanent magnet with Cu coating and DP1180 steel, Cu diffuses in the solder and reacts with Zn and Fe to form brittle intermetallic compounds, resulting in cracks and holes in the soldering seam. The shear strength of the soldered joint of sintered NdFeB permanent magnet with Cu coating and DP1180 steel decreases to 52.3 MPa, compared with that without Cu coating (61.9 MPa). For the soldered joint of sintered NdFeB permanent magnet with Ni coating and DP1180 steel, Ni is concentrated at the interface of NdFeB side, different diffusion layers are formed due to the diffusion of Sn and Bi, and the shear strength of soldered joint increases to 78.1 MPa. |
| |
| Keywords: | sintered NdFeB permanent magnet metal coating soldered joint microstructure shear strength |
|
| 点击此处可从《稀有金属材料与工程》浏览原始摘要信息 |
|
点击此处可从《稀有金属材料与工程》下载全文 |
|
