| 低压铸造中O形密封圈密封特性分析 |
| |
| 引用本文： | 冉迪,郑鹏,王宁,卞思文,韩志,王丹,王晓凤. 低压铸造中O形密封圈密封特性分析[J]. 液压与气动, 2022, 0(2): 56-62. DOI: 10.11832/j.issn.1000-4858.2022.02.008 |
| |
| 作者姓名： | 冉迪 郑鹏 王宁 卞思文 韩志 王丹 王晓凤 |
| |
| 作者单位： | 1.沈阳城市建设学院机械工程学院, 辽宁沈阳 110167; 2.沈阳工业大学机械工程学院, 辽宁沈阳 110870 |
| |
| 基金项目： | 国家自然科学基金青年基金(52005345);辽宁省教育厅科学研究经费项目(LJGD2020003)。 |
| |
| 摘 要： | 为了分析低压铸造高温极端工况下O形密封圈的密封特性及密封失效问题,根据工况顺序,基于Mooney-Rivlin模型,采用ANSYS有限元分析了O形密封圈不同温度、压缩率、介质压力条件下的密封特性及密封失效位置.结果 表明:温度升高、压缩率减小、介质压力增大均使易破损位置向密封槽上过渡圆角处移动;当介质压力为2 MPa,...
|
| 关 键 词： | 低压铸造 O形密封圈 有限元分析 高温 压缩率 介质压力 密封失效 |
| 收稿时间： | 2021-05-06 |
O-ring Sealing Characteristics Analysis in Low Pressure Casting |
| |
| RAN Di,ZHENG Peng,WANG Ning,BIAN Si-wen,HAN Zhi,WANG Dan,WANG Xiao-feng. O-ring Sealing Characteristics Analysis in Low Pressure Casting[J]. Chinese Hydraulics & Pneumatics, 2022, 0(2): 56-62. DOI: 10.11832/j.issn.1000-4858.2022.02.008 |
| |
| Authors: | RAN Di ZHENG Peng WANG Ning BIAN Si-wen HAN Zhi WANG Dan WANG Xiao-feng |
| |
| Affiliation: | 1. School of Mechanical Engineering, Shenyang Urban Construction University, Shenyang, Liaoning 110167; 2. School of Mechanical Engineering, Shenyang University of Technology, Shenyang, Liaoning 110870 |
| |
| Abstract: | In order to analyze the O-ring sealing characteristics and sealing failure under the high temperature in the low pressure casting,according to the working condition sequence,based on the Mooney-Rivlin models,the O-ring sealing characteristics and sealing failure location under the different temperature,compression ratio and medium pressure condition are analyzed by ANSYS finite element analysis.The results show that with the temperature increasing,compression ratio decreasing and medium pressure increasing,the easily damaged position moves to the transition fillet on the sealing groove.When the medium pressure is 2 MPa,the compression ratio is between 10%and 15%,the sealing performance is improved and the failure probability is reduced.When the temperature is 150℃,the medium pressure is higher than 2.5 MPa,and the compression ratio is lower than 5%,the failure probability is increases.The smaller compression ratio reduces the sealing performance,and increases the failure probability. |
| |
| Keywords: | low pressure casting O-ring seal finite element analysis high temperature compression ratio medium pressure sealing failure |
| 本文献已被 维普 等数据库收录！ |
| 点击此处可从《液压与气动》浏览原始摘要信息 |
|
点击此处可从《液压与气动》下载免费的PDF全文 |
|
