|
|||||
|
|
| 选择性激光熔化快速成型工艺研究 | |
| 引用本文： | 陈光霞,曾晓雁,王泽敏,关凯,彭昌吻. 选择性激光熔化快速成型工艺研究[J]. 机床与液压, 2010, 38(1). DOI: 10.3969/j.issn.1001-3881.2010.01.001 |
| 作者姓名： | 陈光霞 曾晓雁 王泽敏 关凯 彭昌吻 |
| 作者单位： | 1. 江汉大学机电与建筑工程学院,湖北武汉,430056 2. 华中科技大学武汉国家光电实验室激光部,湖北武汉,430074 3. 华中科技大学武汉国家光电实验室激光部,湖北武汉,430074 |
| 基金项目： | 国家863高科技项目(2006AA03Z0446) |
| 摘 要： | 利用IPG200W光纤激光器和自主研发的SLM(Selective Laser Melting)快速成型设备,采用不同工艺参数组合,在25mm厚Q235钢板上进行不锈钢粉末单道熔覆实验。研究了激光功率、扫描速度对单道熔覆形貌和宽度、高度的影响规律;分析了选择性激光熔化球化现象产生机理及避免产生球化的途径;论述了最佳工艺参数的获取方法。结果表明:能量密度越高,熔覆形貌越好,球化现象越不明显;激光功率增大,单道熔覆宽度和高度也增加;扫描速度增大,单道熔覆高度和宽度减小。最后给出了几组最佳加工工艺参数和加工实例。 |
| 关 键 词： | 激光快速成型 选择性激光熔化 工艺参数 球化 |
Research on Rapid Prototyping Technology of Selective Laser Melting |
|
| CHEN Guangxia,ZENG Xiaoyan,WANG Zemin,GUAN Kai,PENG Changwen. Research on Rapid Prototyping Technology of Selective Laser Melting[J]. Machine Tool & Hydraulics, 2010, 38(1). DOI: 10.3969/j.issn.1001-3881.2010.01.001 | |
| Authors: | CHEN Guangxia ZENG Xiaoyan WANG Zemin GUAN Kai PENG Changwen |
| Affiliation: | 1.School of Electromechanical and Architectural Engineering;Jianghan University;Wuhan Hubei 430056;China;2.Division of Laser Technology;Wuhan National Laboratory for Optoelectronics;HuazhongUniversity of Science & Technology;Wuhan Hubei 430074;China |
| Abstract: | The single cladding experiments under different process parameters were made on Q235 substrate of 25mm with IPG fiber laser and selective laser melting system manufactured by ourselves.The effect of laser power and scanning velocity on single cladding shape,width and height was studied.The reason of balling in selective laser melting was analyzed and the avoiding method was discussed.The optimum parameters were determined.Experimental results show that the higher laser power density,the better single claddi... |
| Keywords: | Laser rapid prototyping Selective laser melting Process parameters Balling |
| 本文献已被 CNKI 万方数据 等数据库收录！ | |