| 三维整体高翅片强化传热铝管刨削成形机理 |
| |
| 引用本文： | 万珍平,徐燕小,汤勇,徐刚. 三维整体高翅片强化传热铝管刨削成形机理[J]. 中国有色金属学报, 2011, 21(3) |
| |
| 作者姓名： | 万珍平 徐燕小 汤勇 徐刚 |
| |
| 作者单位： | 1. 华南理工大学机械与汽车工程学院,广州,510640
2. 深圳大学机电与控制学院,深圳,518060 |
| |
| 基金项目： | 国家自然科学基金资助项目(50605023,U0934005); 华南理工大学中央高校基本科研业务费专项资金资助项目(2009ZM0168); 深圳市科技计划资助项目(SY200806300289A) |
| |
| 摘 要： | 为了高效加工出三维整体高翅片强化传热管,提出采用多刀刨削加工三维整体高翅片强化传热管的制造方法——利用在基管上同时刨削出多片不脱离工件的、不发生卷曲的切屑作为三维整体高翅片强化传热管的翅片。研究刀具前角、切削厚度对切屑卷曲的影响,初步探讨翅片刨削成形即切屑不卷曲的机理。结果表明,切屑不卷曲的条件是当刀具前角为60°或55°时,切削厚度在0.15~0.25 mm之间,或者前角为50°,切削厚度在0.1~0.2 mm之间时,切屑不发生卷曲;切屑不卷曲的机理在于切屑根部没有发生明显的剪切变形。
|
| 关 键 词： | 三维整体高翅片 强化传热管 刨削 切屑卷曲 |
Planing forming mechanism of integral serrated high finned tube made of aluminum alloy |
| |
| WAN Zhen-ping,XU Yan-xiao,TANG Yong,XU Gang. Planing forming mechanism of integral serrated high finned tube made of aluminum alloy[J]. The Chinese Journal of Nonferrous Metals, 2011, 21(3) |
| |
| Authors: | WAN Zhen-ping XU Yan-xiao TANG Yong XU Gang |
| |
| Affiliation: | WAN Zhen-ping1,XU Yan-xiao1,TANG Yong1,XU Gang2(1.School of Mechanical and Automotive Engineering,South China University of Technology,Guangzhou 510640,China,2.College of Mechatronics and Control Engineering,Shenzhen University,Shenzhen 518060,China) |
| |
| Abstract: | The planing forming using several tools at the same time was proposed to produce the integral serrated high finned tube.By this method,the uncurled chips that are inseparated with base tube are served as integral serrated high fins.The effects of rake angle and cutting thickness on chip curl were investigated and the planing forming mechanism of fins namely chip uncurling was discussed.The experimental results show that the conditions of keeping chip uncurling are that the cutting thickness is 0.15-0.25 mm ... |
| |
| Keywords: | integral serrated high fins heat transfer enhancement tube planing chip curl |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
|
