| 基于平晶的非线性激光扫描直径测量系统 |
| |
| 引用本文： | 王一,任永杰,杨凌辉,叶声华.基于平晶的非线性激光扫描直径测量系统[J].传感技术学报,2012,25(1):58-61. |
| |
| 作者姓名： | 王一 任永杰 杨凌辉 叶声华 |
| |
| 作者单位： | 天津大学精密测试技术及仪器国家重点实验室;北京航空航天大学仪器科学与光电工程学院精密光机电一体化技术教育部重点实验室 |
| |
| 基金项目： | 高档数控机床与基础制造装备科技重大专项(2009ZX04014-092) |
| |
| 摘 要： | 设计了一种基于平晶扫描的轴类零件直径测量系统。激光透射旋转的平晶产生扫描平行光,扫描光偏移光轴的距离是入射角及平晶自身参数的非线性函数,光电检测及计时电路获得测量周期和对应被测工件边缘的信号跳变时间,根据时间与转动角度的比例关系将所得时间量换算成入射角度,最终实现直径测量。利用刀口法进行标定实验,分别采用参数拟合法和RBF神经网络法确定实际非线性测量方程,完成了各测头的标定,进一步实现多测头系统标定,在100 mm的测量范围内,3σ重复性误差为0.006 mm,测量误差为±0.010 mm。
|
| 关 键 词： | 平晶 直径测量 刀口法 RBF神经网络 |
Non-linear Laser Scanning System for Diameter Measurement Based on Flat-crystal |
| |
| WANG Yi,REN Yongjie,YANG Linghui,YE Shenghua.Non-linear Laser Scanning System for Diameter Measurement Based on Flat-crystal[J].Journal of Transduction Technology,2012,25(1):58-61. |
| |
| Authors: | WANG Yi REN Yongjie YANG Linghui YE Shenghua |
| |
| Affiliation: | 1(1.State Key Laboratory of Precision Measuring Technology and Instruments,Tianjin University,Tianjin 300072,China;2.Key Laboratory of Precision Opto-mechatronics Techonology,Ministry of Education,School of InstrumentalScience and Optoelectronics Engineering,Beihang University,Beijing 100191,China) |
| |
| Abstract: | A system used for diameter measurement of shaft parts based on flat-crystal scanning is designed.The parallel scanning beam is generated by laser transmission through rotary flat-crystal.The offset betweeen scanning beam and optical axis is a non-linear function of the incident angle and parameters of the flat-crystal.The time of signal jumping which is corresponding to the edge of the workpiece can be obtained by the photoelectric detection ciucuit and the timing circuit.The diameter is determined by the incident angles calculated according to the scale relation between the time and the rotation angle.Using the knife-edge method,the actual non-linear measuring equation of each sensor is aquired by means of parameter fitting and RBF neural network training and then the multi-sensor syetem is calibrated.Within the mearuement range of 100 mm,the 3σ repeatability error is 0.006 mm and the measurement error is ±0.010 mm. |
| |
| Keywords: | flat-crystal diameter measurement knife-edge method RBF neural network |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《传感技术学报》浏览原始摘要信息 |
|
点击此处可从《传感技术学报》下载全文 |
|
