| ECAPT过程中载荷变化规律的数值模拟 |
| |
| 引用本文： | 张翔,李萍,王晓溪,薛克敏,吴战立. ECAPT过程中载荷变化规律的数值模拟[J]. 精密成形工程, 2010, 2(5): 6-9 |
| |
| 作者姓名： | 张翔 李萍 王晓溪 薛克敏 吴战立 |
| |
| 作者单位： | 合肥工业大学,材料科学与工程学院,合肥,230009 |
| |
| 基金项目： | 国家自然科学基金，霍英东教育基金会，安徽省优秀青年科技基金 |
| |
| 摘 要： | 为了掌握纯铝在ECAPT过程中的力学变化规律,利用刚塑性有限元技术对纯铝1100的ECAPT变形行为进行数值模拟,重点分析了载荷在挤压过程中的变化规律及产生变化的原因。结果表明:ECAPT过程大致分为载荷骤升、2次小幅度升高和载荷下降4个阶段;载荷峰值随着摩擦因数的增大迅速增大,应采取有效的润滑措施减小摩擦从而降低载荷峰值,提高模具寿命;随着摩擦因数的增大,载荷在达到各阶段峰值后下降趋势越来越明显。
|
| 关 键 词： | 大塑性变形 等径角挤压 挤扭 等径角挤扭 数值模拟 |
| 收稿时间： | 2010-05-31 |
| 修稿时间： | 2010-09-10 |
The FEM Numerical Simulation of Loads in ECAPT |
| |
| ZHANG Xiang,LI Ping,WANG Xiao-xi,XUE Ke-min and WU Zhan-li. The FEM Numerical Simulation of Loads in ECAPT[J]. Journal of Netshape Forming Engineering, 2010, 2(5): 6-9 |
| |
| Authors: | ZHANG Xiang LI Ping WANG Xiao-xi XUE Ke-min WU Zhan-li |
| |
| Affiliation: | School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009,China,School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009,China,School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009,China,School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009,China and School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009,China |
| |
| Abstract: | In order to master the variation regularity of mechanics in the ECAPT process, the rigid-plastic FEM has been used in the numerical simulation of ECAPT of aluminum 1100. The load variation and the reasons were mainly investigated. The results show that ECAPT of aluminum 1100 can be classified into four phases in the process: the load increases fast, the load increases slowly two times, the load declines. Peak value of load will increase swiftly with the friction coefficient increasing. An effective lubricating measure should be adopted to reduce the peak value and prolong the mould life. With friction coefficient increasing the load will decline obviously when it reaches the peak value. |
| |
| Keywords: | severe plastic deformation equal channel angular pressing twist extrusion equal channel angular pressing and torsion numerical simulation |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《精密成形工程》浏览原始摘要信息 |
|
点击此处可从《精密成形工程》下载免费的PDF全文 |
|
