| 不同卷烟机型对烟丝造碎的影响 |
| |
| 引用本文： | 邓国栋,堵劲松,张玉海,王锐亮,卢新万,李善莲,徐大勇,王兵. 不同卷烟机型对烟丝造碎的影响[J]. 烟草科技, 2012, 0(8): 8-11 |
| |
| 作者姓名： | 邓国栋 堵劲松 张玉海 王锐亮 卢新万 李善莲 徐大勇 王兵 |
| |
| 作者单位： | 1. 中国烟草总公司郑州烟草研究院烟草行业烟草工艺重点实验室,郑州高新技术产业开发区枫杨街2号,450001
2. 福建中烟工业公司,福建省厦门市海沧新阳工业区新阳路1号,361026 |
| |
| 基金项目： | 国家烟草专卖局资助项目“卷制过程烟丝破碎度的测定方法” |
| |
| 摘 要： | 为分析不同卷烟机型对卷制过程烟丝造碎程度的影响,研究了PROTOS,PASSIM和SUPER9 3种型号卷接机组卷制前后烟丝结构的变化,通过特征尺寸计算不同卷烟机型对烟丝的破碎度,由破碎度分析不同卷烟机型对烟丝的造碎程度。结果表明:①对于同种配方烟丝,PASSIM卷烟机的造碎程度最小,PROTOS卷烟机其次,SUPER9卷烟机对配方烟丝的造碎程度最大;②同一卷烟机型对不同配方烟丝比例的配方造碎程度存在差异,叶丝比例高、梗丝比例低的烟丝经卷烟机卷制后造碎程度高。
|
| 关 键 词： | 烟丝破碎度 卷烟机 特征尺寸 造碎 |
Influences of Cigarette Maker Type on Tobacco Breakage |
| |
| DENG Guodong , DU Jinsong , ZHANG Yuhai , WANG Ruiliang , LU Xinwan , LI Shanlian , XU Dayong , WANG Bing. Influences of Cigarette Maker Type on Tobacco Breakage[J]. Tobacco Science & Technology, 2012, 0(8): 8-11 |
| |
| Authors: | DENG Guodong DU Jinsong ZHANG Yuhai WANG Ruiliang LU Xinwan LI Shanlian XU Dayong WANG Bing |
| |
| Affiliation: | 1.Key Laboratory of Tobacco Processing Technology of CNTC,Zhengzhou Tobacco Research Institute of CNTC,Zhengzhou 450001,China 2.Technology Center of China Tobacco Fujian Industrial Co.,Ltd.,Xiamen 361026,Fujian,China |
| |
| Abstract: | In order to study the influences of cigarette makers of different types on tobacco breakage during cigarette manufacturing,the changes of cut tobacco size distribution before and after cigarette manufacturing in PROTOS,PASSIM and SUPER9 cigarette makers were analyzed respectively.The degrees of breakage were calculated by means of characteristic size of cut tobacco.The results showed that: 1) for cut tobacco of the same blend,the makers in the order of cut tobacco shattering degree were PASSIM
|
| |
| Keywords: | Breakage degree of cut tobacco Cigarette maker Characteristic size Shattering |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
|
