| 工艺条件对注射成型PP/POE共混制品结晶度的影响 |
| |
| 引用本文： | 曾盛渠,黄志高,周华民,刘芬,邓林.工艺条件对注射成型PP/POE共混制品结晶度的影响[J].高分子材料科学与工程,2011(10):134-137,142. |
| |
| 作者姓名： | 曾盛渠 黄志高 周华民 刘芬 邓林 |
| |
| 作者单位： | 华中科技大学材料成形与模具技术国家重点实验室; |
| |
| 基金项目： | 国家自然科学基金资助项目(50875095); 国家863项目(2009AA03Z104) |
| |
| 摘 要： | 以矩形聚丙烯(PP)/乙烯-辛烯共聚物(POE)共混制品为例,研究了注射成型工艺参数对结晶度的影响规律。通过扫描电子显微镜(SEM)得到POE分散相含量,结合差示扫描量热仪(DSC)获得PP基体的绝对结晶度。实验结果表明,通常表层的结晶度最低,例外的是在最高注射速率条件下,表层内0.2 mm处结晶度最小;随保压压力增大结晶度减小;高的熔体温度会使剪切形成的晶核前驱(precursor)被重新融化,取向松弛,弱化充填中剪切诱导作用,造成结晶度减小;高的注射速率提高了充填结束后型腔内熔体温度,对结晶度的影响类似提高熔体温度;在低熔体温度和低注射速率条件下成型可获得高的结晶度。
|
| 关 键 词： | 聚丙烯/乙烯-辛烯共聚物共混 差示扫描量热 注射成型 工艺参数 结晶度 |
Effect of Processing Conditions on the Depth Distribution of Crystallinity of Injection Molded PP/POE Blends |
| |
| Shengqu Zeng,Zhigao Huang,Huamin Zhou,Fen Liu,Lin Deng.Effect of Processing Conditions on the Depth Distribution of Crystallinity of Injection Molded PP/POE Blends[J].Polymer Materials Science & Engineering,2011(10):134-137,142. |
| |
| Authors: | Shengqu Zeng Zhigao Huang Huamin Zhou Fen Liu Lin Deng |
| |
| Affiliation: | Shengqu Zeng,Zhigao Huang,Huamin Zhou,Fen Liu,Lin Deng(State Key Laboratory of Material Processing and Die & Mould Technology,HuazhongUniversity of Science and Technology,Wuhan 430074,China) |
| |
| Abstract: | This study is concern with the effect of processing conditions on depth distribution of crystallinity of PP in injection molded isotactic polypropylene(PP) /ethylene-octane copolymer(POE) blends with fixed mass ratio(75/25).POE content was calculated from scanning electron microscope(SEM) pictures,then depth distribution of absolute crystallinity of PP was calculated by enthalpy of fusion measured through differential scanning calorimetry(DSC).The results indicate that the crystallinity of outmost skin is 7... |
| |
| Keywords: | polypropylene /ethylene-octane copolymer blends DSC injection molding processing condition absolute crystallinity |
| 本文献已被 CNKI 等数据库收录！ |
|
