| 中国低活化钢激光焊接接头微观组织与硬度分析 |
| |
| 引用本文： | 雷玉成,韩明娟,朱强,巨新.中国低活化钢激光焊接接头微观组织与硬度分析[J].焊接学报,2010,31(1):5-8. |
| |
| 作者姓名： | 雷玉成 韩明娟 朱强 巨新 |
| |
| 作者单位： | 1. 江苏大学材料科学与工程学院,镇江,212013
2. 北京科技大学物理系,北京,100083 |
| |
| 基金项目： | 国家重点基础研究计划[973计划]资助项目(2008CB717802);;江苏大学科技创新团队资助项目 |
| |
| 摘 要： | 采用功率为4 kW的Nd:YAG激光器,对6 mm厚CLAM钢板采用不同的焊接参数进行了激光焊接试验,焊后对部分试样进行回火处理.分别对焊后和回火试样的硬度和微观组织结构进行了测试和观察.结果表明,回火处理前焊接接头金相组织主要为粗大的板条马氏体,随着焊接速度的提高,焊缝硬度有所提高;回火处理后焊接接头金相组织为板条特征明显的回火马氏体,使用扫描电镜对回火后焊接接头进行观察发现在原奥氏体晶界和马氏体板条上有碳化物析出,导致焊缝区的硬度相对母材略有提高,焊接热影响区未出现软化现象.
|
| 关 键 词： | 低活化马氏体钢 中国低活化马氏体钢 YAG激光焊 组织结构 硬度 |
| 收稿时间： | 2009/4/13 0:00:00 |
Microstructure and hardness of laser welded joint of China low activation martensitic steel |
| |
| LEI Yucheng,HAN Mingjuan,ZHU Qiang and JU Xin.Microstructure and hardness of laser welded joint of China low activation martensitic steel[J].Transactions of The China Welding Institution,2010,31(1):5-8. |
| |
| Authors: | LEI Yucheng HAN Mingjuan ZHU Qiang and JU Xin |
| |
| Affiliation: | 1.School of Material Science and Engineering of Jiangsu University;Zhenjiang 212013;Jiangsu;China;2.Physics Department;University of Science and Technology of Beijing;Beijing 100083;China |
| |
| Abstract: | Laser welding of 6mm-thick CLAM is conducted with different welding parameters by 4 kW Nd:YAG.Microstructure and hardness of welded joint are analyzed with pre-and post tempering respectively.The results show that the microstructure of welded joints are mainly coarse lath martensite and hardness of welded joint is increased as welding speed rises before tempering.After tempering,microstructure of welded joint is tempered lath martensite.A large amount of carbide particles are observed in original austenite ... |
| |
| Keywords: | low activation martensitic steel CLAM YAG laser welding microstructure hardness |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载全文 |
