| 热处理工艺对12Cr1MoV钢组织性能的影响 |
| |
| 引用本文： | 王贞,刘静,鲁修宇,邓照军.热处理工艺对12Cr1MoV钢组织性能的影响[J].热处理技术与装备,2012,33(2):10-14. |
| |
| 作者姓名： | 王贞 刘静 鲁修宇 邓照军 |
| |
| 作者单位： | 1. 武汉科技大学钢铁冶金及资源利用省部共建教育部重点实验室,湖北武汉,430081
2. 武汉钢铁(集团)公司研究院,湖北武汉,430080 |
| |
| 摘 要： | 通过常规力学性能测试设备、光学显微镜研究了不同热处理工艺对12Cr1MoV钢性能和组织的影响。结果表明:随着正火温度提高,12Cr1MoV钢的抗拉强度和屈服强度变化不大,而冲击韧性有较大增加;随着回火温度提高,经910℃和930℃两种正火温度处理,12Cr1MoV钢的强度和韧性变化不大。12Cr1MoV钢在热轧态、正火态及正火+回火态的组织均为铁素体+珠光体,经910℃正火+680℃回火处理后,钢中的铁素体晶粒度比930℃正火+680℃回火处理后更细小且分布更均匀,性能与前者基本相同。因此,可以选取910℃正火+680℃回火作为12Cr1MoV钢的热处理工艺,从而降低钢板生产的成本。
|
| 关 键 词： | 锅炉用钢 12Cr1MoV 组织 热处理 |
Effects of Heat Treatment Process on the Microstructures and Properties of 12Cr1MoV Steel |
| |
| WANG Zhen
,
LIU Jing
,
LU Xiu-yu
,
DENG Zhao-jun.Effects of Heat Treatment Process on the Microstructures and Properties of 12Cr1MoV Steel[J].Heat Treatment Technology and Equipment,2012,33(2):10-14. |
| |
| Authors: | WANG Zhen LIU Jing LU Xiu-yu DENG Zhao-jun |
| |
| Affiliation: | 1.Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education,Wuhan University of Science and Technology,Wuhan Hubei 430081,China;2.Research and Development Academy, Wuhan Iron and Steel Corporation,Wuhan Hubei 430080,China) |
| |
| Abstract: | The effect of heat treatment process on the mechanical property and microstructure of 12Cr1MoV steel was researched by traditional mechanical testing equipment and OM.The results of heat treatment showed that the tensile strength and yield strength have a little change and the impact toughness has a large increase with the increase of the normalizing temperature.The strength and toughness of the 12Cr1MoV steel under 910 ℃ and 930 ℃ normalizing change a little with the increase of the tempering temperature.The microstructures of 12Cr1MoV steel as all the hot rolled,normalized and normalized+ tempered are ferrite and pearlite.After 910 ℃ normalizing + 680 ℃ tempering,the grain size of ferrite is more fine and more homogenous than ones of 930 ℃ normalizing + 680 ℃ tempering,and the properties are basically the same.So it is feasible and reasonable to select the heat treatment of 910 ℃ normalizing + 680 ℃ tempering,so as to reduce the cost of steel production. |
| |
| Keywords: | boiler steel 12Cr1MoV microstructure heat treatment |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
|
