| 电镀金刚石线锯镀镍层力学性能及磨粒把持力研究 |
| |
| 引用本文： | 谢乾,葛培琪,孟剑峰,毕文波,马晓宾,郑楚夕,龚洋. 电镀金刚石线锯镀镍层力学性能及磨粒把持力研究[J]. 金刚石与磨料磨具工程, 2020, 40(1): 50-55. DOI: 10.13394/j.cnki.jgszz.2020.1.0008 |
| |
| 作者姓名： | 谢乾 葛培琪 孟剑峰 毕文波 马晓宾 郑楚夕 龚洋 |
| |
| 作者单位： | 1. 山东大学 机械工程学院, 济南 250061;2. 山东大学高效洁净机械制造教育部重点试验室, 济南 250061;3. 山田新材科研有限公司, 山东 临沂 276700 |
| |
| 基金项目： | 国家自然科学基金;山东省重点研发计划 |
| |
| 摘 要： | 电镀工艺参数直接影响电镀金刚石线锯镀镍层的力学性能且难以测定。按金刚石线锯电镀工艺制备电镀试件，利用纳米压/划痕仪、X射线衍射仪测试试件的力学性能，得镀镍层的硬度、弹性模量、残余应力以及镀镍层与线锯基体的结合强度。简化计算镀镍层对金刚石磨粒的把持力。根据试验获得的镀镍层力学参数建立磨粒把持力有限元模型并进行仿真分析。简化计算与仿真分析的结果一致性较好。
|
| 关 键 词： | 电镀金刚石线锯 镀镍层 金刚石磨粒 把持力 |
Study on mechanical properties of nickel-plated layer and abrasive holding force of electroplated diamond wire saw |
| |
| XIE Qian,GE Peiqi,MENG Jianfeng,BI Wenbo,MA Xiaobin,ZHENG Chuxi,GONG Yang. Study on mechanical properties of nickel-plated layer and abrasive holding force of electroplated diamond wire saw[J]. Diamond & Abrasives Engineering, 2020, 40(1): 50-55. DOI: 10.13394/j.cnki.jgszz.2020.1.0008 |
| |
| Authors: | XIE Qian GE Peiqi MENG Jianfeng BI Wenbo MA Xiaobin ZHENG Chuxi GONG Yang |
| |
| Affiliation: | 1. School of Mechanical Engineering, Shandong University, Jinan 250061, China;2. Key Laboratory of High-Efficiency and Clean Mechanical Manufacture at Shandong University, Ministry of Education, Jinan 250061, China;3. Shantian Abrasive Materials Limited Company, Linyi 276700, Shandong, China |
| |
| Abstract: | The mechanical properties of nickel coating on electroplated diamond wire saw are directly affected by electroplating process parameters,which are difficult to determine.Electroplating specimens were prepared according to the electroplating process of diamond wire saw.The mechanical properties of the specimens were tested by nanoindentation/scratch tester and X-ray diffractometer.The hardness,modulus of elasticity,residual stress of nickel-plated layer and the bonding strength between nickel-plated layer and wire saw matrix were obtained.The holding force of nickel plating on diamond abrasive particles was calculated.According to the mechanical parameters of nickel coating obtained from the test,the finite element model of abrasive holding force is established and simulated.The simplified calculation results are in good agreement with the simulation results. |
| |
| Keywords: | electroplated diamond wire saw nickel plating layer diamond abrasives holding force |
| 本文献已被 CNKI 维普 万方数据 等数据库收录！ |
| 点击此处可从《金刚石与磨料磨具工程》浏览原始摘要信息 |
|
点击此处可从《金刚石与磨料磨具工程》下载免费的PDF全文 |
