| Zn-Al钎料钎焊6063铝合金铺展性能及接头断裂机理分析 |
| |
| 引用本文： | 张满,夏之穹,张临财,徐鸿宾.Zn-Al钎料钎焊6063铝合金铺展性能及接头断裂机理分析[J].焊接学报,2015,36(8):63-66. |
| |
| 作者姓名： | 张满 夏之穹 张临财 徐鸿宾 |
| |
| 作者单位： | 1.淮阴工学院机械工程学院, 淮安 223003 |
| |
| 基金项目： | 江苏省高等学校大学生创新创业训练计划资助项目(201511049042Y);江苏省自然科学基金资助项目(BK20140458);淮阴工学院青年科研基金资助项目(HGC1017) |
| |
| 摘 要： | 研究了Zn-Al钎料钎焊6063铝合金的铺展性能及接头断裂机理.钎料铺展试验表明,随着钎料中铝含量的增加,钎料铺展面积增大,铝含量增至22%(质量分数)时,钎料铺展面积达到最大,继续增加铝含量,铺展面积减小.钎焊接头力学性能试验表明,随着钎料中铝含量的增加,铝基固溶体强化相数量增加,搭接钎焊接头强度提高,铝含量增至22%(质量分数)时,钎焊接头强度达到最高,继续增加铝含量,钎缝内枝状共析组织变得粗大,与其周围组织之间容易产生应力集中,萌生裂纹,钎焊接头强度降低.综合考虑钎料的铺展性能以及钎焊接头力学性能,78Zn-22Al钎料钎焊6063铝合金性能最佳.
|
| 关 键 词： | Zn-Al钎料 钎焊 6063铝合金 铺展性能 力学性能 |
| 收稿时间： | 2015/2/12 0:00:00 |
Spreadability of Zn-Al filler metal and fracture mechanism of 6063 Al-alloy brazed joint |
| |
| ZHANG Man,XIA Zhiqiong,ZHANG Lincai and XU Hongbin.Spreadability of Zn-Al filler metal and fracture mechanism of 6063 Al-alloy brazed joint[J].Transactions of The China Welding Institution,2015,36(8):63-66. |
| |
| Authors: | ZHANG Man XIA Zhiqiong ZHANG Lincai and XU Hongbin |
| |
| Affiliation: | 1.Department of Mechanical Engineering, Huaiyin Institute of Technology, Huai'an 223003, China2.Jiangsu Provincial Key Laboratory for Interventional Medical Devices, Huaiyin Institute of Technology, Huai'an 223003, China |
| |
| Abstract: | The spreadability of Zn-Al filler metal on 6063 Al-alloy surface were investigated, moreover, the strength and microstructure of 6063 Al-alloy lap-joints were studied. The results indicated that spreadability was improved with the increase of Al content in filler metal. When Al content was 22%, the filler metal got the best spreadability on 6063 Al-alloy surface. However, the spreadability decreased when Al content exceeded 22%. Furthermore, the brazed lap-joint mechanical property test results indicated that the strength of 6063 Al-alloy lap-joint was enhanced with the increase of Al content in filler metal. The highest strength of brazed joint was obtained when Al content is 22%, however, when Al content exceeded 22%, the dentritic eutectoid structure became larger in the brazing joint. Stress concentration emerged easily between large dendritic eutectoid structure and the surrounding structure. And the strength of brazed joint decreased gradually. The optimum fill metal possessing best comprehensive properties is 78Zn-22Al filler metal. |
| |
| Keywords: | Zn-Al filler metal brazing 6063 Al-alloy spreadability mechanical property |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载全文 |
|
