| 基于PFM调节的脉冲MIG焊电弧调节机理分析 |
| |
| 引用本文： | 张晓莉,林放,李钰桢,薛家祥.基于PFM调节的脉冲MIG焊电弧调节机理分析[J].焊接学报,2013(12):83-87. |
| |
| 作者姓名： | 张晓莉 林放 李钰桢 薛家祥 |
| |
| 作者单位： | 江西理工大学机电工程学院, 赣州 341000;华南理工大学机械与汽车工程学院, 广州 510640,江门职业技术学院机电技术系, 江门 529000,华南理工大学机械与汽车工程学院, 广州 510640,华南理工大学机械与汽车工程学院, 广州 510640 |
| |
| 基金项目： | 广东省特派员工作站资助项目(2010B090500008);佛山市科技计划资助项目(2011AA100175);黄埔区科技计划资助项目(201341) |
| |
| 摘 要： | 针对脉冲MIG焊电源弧长控制方面存在的问题,展开对脉冲MIG焊电弧自我调节机理以及在脉频调制(PFM)控制下的电弧调节机理的研究.建立了电弧弧长数学模型,分析了PFM双闭环电弧调节系统的工作原理,给出了PFM电流调节数学模型,并分析了非阻性焊丝和阻性焊丝PFM电弧控制机理及在电弧控制中存在的问题.从理论上推导出对于非阻性焊丝PFM电流调节可以获得更稳定的焊接效果,而对阻性焊丝CTWD固定时可获得稳定的焊接效果,在CTWD变化时无法获得满意的焊接效果.最后分别对阻性焊丝和非阻性焊丝进行PFM电弧调节阶跃试验,通过对试验结果分析,验证了上述理论推导.
|
| 关 键 词： | PFM调节 脉冲MIG焊 电弧 阻性焊丝 非阻性焊丝 |
| 收稿时间： | 2013/8/30 0:00:00 |
Analysis of arc adjustment mechanism to pulsed MIG welding based on PFM adjustment |
| |
| ZHANG Xiaoli,LIN Fang,LI Yuzhen and XUE Jiaxiang.Analysis of arc adjustment mechanism to pulsed MIG welding based on PFM adjustment[J].Transactions of The China Welding Institution,2013(12):83-87. |
| |
| Authors: | ZHANG Xiaoli LIN Fang LI Yuzhen and XUE Jiaxiang |
| |
| Affiliation: | College of Mechanical and Electrical Engineering, Jiangxi University of Science & Technology, Ganzhou 341000, China;School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640, China,Department of Electromechanical, Jiangmen Polytechnic College, Jiangmen 529000, China,School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640, China and School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640, China |
| |
| Abstract: | Aimed at the problems of arc length control in pulsed MIG welding power supply,the research of arc self-regulating mechanism and arc adjusting mechanism under the control of the pulse frequency modulation (PFM) was developed.The mathematical model of arc length was established.The principle of PFM arc adjustment system was introduced and the PFM current regulation model was given.The PFM arc control mechanism and the problems existing in the arc control were analyzed for non-resistance wire and resistance wire.A more stable welding effect can be obtained for PFM current regulation of non-resistance wire from theoretical derivation.For the resistance wire, the stable welding effect can be obtained when CTWD is fixed and satisfactory welding results cannot be obtained while CTWD changing.Finally the step tests of PFM arc adjustment were carried out by using non-resistance wire and resistance wire,respectively.The theory above is verified by test results. |
| |
| Keywords: | PFM adjustment pulsed MIG welding arc resistance wire non-resistance wire |
|
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载全文 |
|
