| 沉积温度对高功率脉冲磁控溅射AlCrSiN涂层结构和性能的影响* |
| |
| 引用本文： | 王铁钢,李柏松,张姣姣,唐宽瑜,刘艳梅,姜素猛.沉积温度对高功率脉冲磁控溅射AlCrSiN涂层结构和性能的影响*[J].稀有金属材料与工程,2018,47(8):2578-2584. |
| |
| 作者姓名： | 王铁钢 李柏松 张姣姣 唐宽瑜 刘艳梅 姜素猛 |
| |
| 作者单位： | 天津职业技术师范大学天津市高速切削与精密加工重点实验室;中国科学院金属研究所 |
| |
| 基金项目： | 国家自然科学(51301181)；天津市应用基础与前沿技术研究计划重点项目(15JCZDJC39700)；天津市高等学校创新团队培养计划项目(TD12-5043) |
| |
| 摘 要： | 采用高功率脉冲磁控溅射(HiPIMS)技术在不同沉积温度下制备了Al-Cr-Si-N涂层。系统研究了沉积温度对涂层结构、成分、显微形貌、力学和摩擦学性能的影响。结果表明:随着沉积温度由100℃升至350℃,涂层内部开始由非晶向纳米晶转化,300℃时出现fcc-AlN相;涂层平整性和致密性逐步改善,膜/基结合强度逐渐提高,在300℃达到最大值77 N,但温度继续升高至350℃时,严重的轰击刻蚀作用使临界载荷骤降至25 N;涂层硬度逐渐增加,在350℃达到最大值19.4GPa;涂层内应力整体呈下降趋势,由–0.8 GPa逐渐降低至–0.4 GPa左右。
|
| 关 键 词： | HiPIMS AlCrSiN涂层 沉积温度 力学性能 摩擦系数 |
| 收稿时间： | 2017/12/18 0:00:00 |
| 修稿时间： | 2018/1/12 0:00:00 |
Influence of Deposition Temperature on Microstructures and Mechanical Properties of Al-Cr-Si-N Coatings Deposited by HiPIMS Technology |
| |
| WANG Tiegang,LI Baisong,ZHANG Jiaojiao,TANG Kuanyu,LIU Yanmei and JIANG Sumeng.Influence of Deposition Temperature on Microstructures and Mechanical Properties of Al-Cr-Si-N Coatings Deposited by HiPIMS Technology[J].Rare Metal Materials and Engineering,2018,47(8):2578-2584. |
| |
| Authors: | WANG Tiegang LI Baisong ZHANG Jiaojiao TANG Kuanyu LIU Yanmei and JIANG Sumeng |
| |
| Affiliation: | Tianjin Key Laboratory of High Speed Cutting and Precision Manufacturing,Tianjin University of Technology and Education,Tianjin,Tianjin Key Laboratory of High Speed Cutting and Precision Manufacturing,Tianjin University of Technology and Education,Tianjin,Tianjin Key Laboratory of High Speed Cutting and Precision Manufacturing,Tianjin University of Technology and Education,Tianjin,Tianjin Key Laboratory of High Speed Cutting and Precision Manufacturing,Tianjin University of Technology and Education,Tianjin,Tianjin Key Laboratory of High Speed Cutting and Precision Manufacturing,Tianjin University of Technology and Education,Tianjin,Institute of Metal Research,Chinese Academy of Sciences,Shenyang |
| |
| Abstract: | High power pulsed magnetron sputtering (HiPIMS) technology can be used to prepare high quality coatings with smooth surface and dense structure due to its high ionization rate and high ion energy. And the deposition temperature will determine the kinetic energy and diffusion ability of the deposited particles, which has a significant impact on the growth process and performance. In this paper, Al-Cr-Si-N coating is prepared by HiPIMS technology at different deposition temperatures. The effects of deposition temperature on the structure, composition, microstructure, mechanical properties and tribological properties of the coatings were systematically studied. The results show that as the deposition temperature rises from 100°C to 350°C, the interior of the coating begins to convert from amorphous to nanocrystals, and the FCC-AlN phase appears at 300°C. The smoothness and compactness of the coatings are progressively improved. The adhesion strength increase gradually, reached the maximum value of 83N at 300 °C and decreases to 18N at 350 °C due to the serious glow etching effect .The hardness of the coating increases gradually and reaches a maximum of 19 GPa at 350°C. No columnar crystals are found and the residual stress is low, and the inverse Hallpez effect occurs, due to the increase in kinetic energy of the deposited particles and the densification of the structure. |
| |
| Keywords: | HiPIMS Al-Cr-Si-N coatings deposition temperature mechanical properties friction coefficient |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《稀有金属材料与工程》浏览原始摘要信息 |
|
点击此处可从《稀有金属材料与工程》下载全文 |
|
