| 浮杯泵柱塞副变形的有限元分析 |
| |
| 引用本文： | 杨磊,高文涛,杨国来,白桂香,景泳淼,陈晨. 浮杯泵柱塞副变形的有限元分析[J]. 液压与气动, 2018, 0(7): 41-46. DOI: 10.11832/j.issn.1000-4858.2018.07.007 |
| |
| 作者姓名： | 杨磊 高文涛 杨国来 白桂香 景泳淼 陈晨 |
| |
| 作者单位： | 1. 海军驻北京地区舰船设备军事代表室， 北京100176；2. 兰州理工大学能源与动力工程学院， 甘肃兰州730050；3. 兰州理工大学兰石研究院， 甘肃兰州730050； 4. 中石油昆仑燃气有限公司浙江分公司， 浙江杭州310000 |
| |
| 基金项目： | 甘肃省科技重大专项（17ZD2GA010)；甘肃省自然科学基金（1606RJYA293） |
| |
| 摘 要： | 浮杯泵独特的结构导致其泄漏点大量增加，变形后的柱塞副密封间隙成为影响其工作性能的主要因素。在泄漏间隙理论分析的基础上利用有限元软件对三组不同柱塞腔尺寸的柱塞和浮杯在上死点和下死点两种极端位置处进行受压变形仿真，讨论变形后柱塞腔的尺寸对柱塞副间隙的影响。分析得到柱塞和浮杯变形后的变化规律，以及在密封线处浮杯的变形值约为0.8 μm和柱塞头的椭圆形变形趋势，对比得出在20 MPa的压力下直径为8 mm、深度为6 mm的柱塞腔能够使柱塞头的变形有效补偿浮杯的变形。
|
| 关 键 词： | 浮杯泵 柱塞 浮杯 柱塞腔 |
| 收稿时间： | 2018-02-14 |
Finite Element Analysis of Plunger Pair Deformation for Floating Cup Pump |
| |
| YANG Lei,GAO Wen-tao,YANG Guo-lai,BAI Gui-xiang,JING Yong-miao,CHEN Chen. Finite Element Analysis of Plunger Pair Deformation for Floating Cup Pump[J]. Chinese Hydraulics & Pneumatics, 2018, 0(7): 41-46. DOI: 10.11832/j.issn.1000-4858.2018.07.007 |
| |
| Authors: | YANG Lei GAO Wen-tao YANG Guo-lai BAI Gui-xiang JING Yong-miao CHEN Chen |
| |
| Affiliation: | 1. Beijing Station, Deputy of Navy Ships Navy, Beijing100176；2. College of Energy and Power Engineering， Lanzhou University of Technology， Lanzhou， Gansu730050; 3. Ls Research Institute， Lanzhou University of Technology， Lanzhou， Gansu730050; 4. Zhejiang Branch of Petrochina Kunlun Gas Co., Ltd., Hangzhou, Zhejiang310000 |
| |
| Abstract: | The unique structure of floating cup pump leads to a large increase of leakage point, and plunger pair sealing gap after deformation becomes a major factor affecting its performance. On the basis of theoretical analysis of leakage gap, we use the finite element software to simulate compression deformation of floating cup and plungers with three different plunger cavity sizes, at two extreme conditions of top dead center and bottom dead center, and discuss the effect of plunger cavity size on plunger pair clearance after deformation. The variation laws of plunger and floating cup after deformation are obtained, and the deformation value of floating cup at sealing line is approximately 0.8 μm, and the trend of elliptical deformation of plunger head is obtained. The result shows that a plunger cavity with a diameter of 8 mm and a depth of 6 mm under a pressure of 20 MPa can make deformation of plunger head effectively compensate for deformation of floating cup. |
| |
| Keywords: | |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《液压与气动》浏览原始摘要信息 |
|
点击此处可从《液压与气动》下载免费的PDF全文 |
|
