首页 | 本学科首页   官方微博 | 高级检索  
     

杯形薄壁矩形内齿旋压成形数值模拟与试验
引用本文:夏琴香,杨明辉,胡昱,程秀全. 杯形薄壁矩形内齿旋压成形数值模拟与试验[J]. 机械工程学报, 2006, 42(12): 192-196
作者姓名:夏琴香  杨明辉  胡昱  程秀全
作者单位:华南理工大学机械工程学院,广州,510640;广州民航职业技术学院机务工程系,广州,510403
基金项目:国家自然科学基金;广东省自然科学基金
摘    要:为研究主要工艺参数对齿轮成形状况的影响规律,并为参数优化和工艺设计提供依据,基于MSC.MARC有限元分析软件,对杯形薄壁矩形内齿旋压成形工艺过程和工艺特点进行分析,从而获得旋压成形时变形金属沿轴向、径向和切向的流动规律。结合工艺试验,定量地研究了主要工艺参数对齿高成形的影响规律,并对试验中出现的各种典型缺陷进行分析,提出有效的预防和改进方法。提出将包括轮齿的切向和轴向尺寸均匀程度等作为旋压成形内齿零件的主要质量评价指标。模拟和工艺试验结果表明,矩形内齿旋压成形时,压下量在一定范围内对齿高的成形影响显著,进给比对齿高成形影响不大。当工艺参数选择不当时,可能出现表面隆起或破裂、轮齿周向错移、周向高度不均和齿槽撕裂等缺陷。

关 键 词:旋压  内齿轮  数值模拟  工艺参数
修稿时间:2006-03-28

NUMERICAL SIMULATION AND EXPERIMENTATION CUP-SHAPED THIN-WALLED INNER RECTANGULAR GEAR FORMED BY SPINNING
XIA Qinxiang,YANG Minghui,HU Yu,CHENG Xiuquan. NUMERICAL SIMULATION AND EXPERIMENTATION CUP-SHAPED THIN-WALLED INNER RECTANGULAR GEAR FORMED BY SPINNING[J]. Chinese Journal of Mechanical Engineering, 2006, 42(12): 192-196
Authors:XIA Qinxiang  YANG Minghui  HU Yu  CHENG Xiuquan
Affiliation:College of Mechanical Engineering, South China University of Technology Department of Airplane Maintenance Engineering, Guangzhou Civil Aviation College
Abstract:In order to investigate the effects of the main proc- essing parameters on the forming situation of the tooth depth, and provide foundation of the corresponding parameter optimi- zation and process design,the forming process and the process characteristics of the cup-shaped thin-walled inner rectangular gear formed by spinning are analyzed based on the MSC.MARC finite element analysis(FEA)software.Combin- ing with the processing experiment,the deformation mechanism of the deformed metal flow along the axial,radial and tangential directions are obtained;the effects of the processing parameters on the forming situation of the tooth depth are studied quantita- tively;the typical defects occurred during spinning are analyzed and the effective prevention methods are put forward.The main indexes to evaluate quality of the inner gear formed by spinning are presented,including the rear tooth dimension uniformity in the tangent and axial directions.Both the simulation and ex- periment results show that:During the spinning of the cup-shaped thin-walled inner rectangular gear,the effect of the blank radius reduction on the tooth depth is significant;The effect of the roller feed rate is slight.When adopting unreason- able processing parameters,the forming defects,such as the piling,fracture,stagger and uneven depth of the gear teeth along the circumferential direction,tearing of the gullet,may occur.
Keywords:Spinning  Inner gear  Numerical simulation  Processing parameter
本文献已被 CNKI 万方数据 等数据库收录!
点击此处可从《机械工程学报》浏览原始摘要信息
点击此处可从《机械工程学报》下载全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号